TK55253.FeederIDLog.pdf - 第4页

Product Engineering Division SMT Sect ion Robotics Operations Y AMAHA MOTOR CO., L TD MDOC-SOFT50281 4/ 15 Fig.3.1 Fee der ID log scr een 3.1.1 Display items The display i tems of feeder I D log screen are as f ollow s. …

100%1 / 15
Product Engineering Division
SMT Section
Robotics Operations
YAMAHA MOTOR CO., LTD
MDOC-SOFT50281
3/15
1. Applicable models and software versions
Applicable feeders and software version are as below.
Table1.1 Applicable feeders and software version
Feeders Software Version Remarks
CLi feeder,
FSi feeder
V3.42STD R1.000 or later YG300,
YG12 series mounters
SS feeder,
ZS feeder
V3.42STD R1.000 or later
V4.42STD R1.000 or later
YS series mounters,
YSM series mounters
Auto Loading Feeder only V3.49STD R3.000 or later
V4.63STD R4.000 or later
YS series mounters,
YSM series mounters
2. Outline
Feeder ID Log function is able to manage the information about feeder usage condition,
error frequency, etc. for each one feeder (each feeder ID) by identifying feeder ID of each
feeder. However, target feeders are only SS feeder, ZS feeder, Auto Loading Feeder
▲2
, CLi
feeder, and FSI feeder.
To use this function, it is necessary to validate Feeder Maintenance Notice function. When
the first installation, Feeder Maintenance Notice function becomes effective by default.
3. Detail
This chapter explains about the feeder ID log screen and the feeder ID log file.
3.1 Feeder ID log screen
The feeder ID log is displayed at [Unit Log]-[Feeder ID] tab.
“Feeder ID” tab is further divided into three tabs. The "Operator" or "Service" tab can be
cleared as needed. The "Total" log cannot be cleared.
Product Engineering Division
SMT Section
Robotics Operations
YAMAHA MOTOR CO., LTD
MDOC-SOFT50281
4/15
Fig.3.1 Feeder ID log
screen
3.1.1 Display items
The display items of feeder ID log screen are as follows.
When feeder is attached or machine is turned on, the last saved data is displayed. If the
last saved data does not exist, the initial value is displayed.
Table3.1 Display items of feeder ID log screen
Column name Contents
Feeder Set No Set position number of attached feeder is displayed.
Feeder ID Feeder ID is displayed.
Feeder Type Feeder type specified by parts data is displayed.
In the case of the feeder unused by board data, the last feeder
type is displayed.
Column name Contents
Parts Name Parts name attached to the feeder is displayed.
In the case of the parts unused by board data, the last parts name
is displayed.
Feeder Counter Number of times of feeder drive (number of shots) is displayed.
This count is used as the standard when calculating various error
ratios.
Product Engineering Division
SMT Section
Robotics Operations
YAMAHA MOTOR CO., LTD
MDOC-SOFT50281
5/15
Pick Error Counter Number of pick error of the parts on the feeder is displayed.
Pick Error % Ratio of “Pick Error Counter” / “Feeder Counter” is displayed.
Vision Error Counter Number of vision error of the parts on the feeder is displayed.
Vision Error % Ratio of “Vision Error Counter” / “Feeder Counter” is displayed.
No Parts Error Counter Number of no-parts error of the parts on the feeder is displayed.
No Parts Error % Ratio of "No Parts Error Counter" / "Feeder Counter" is displayed.
Nozzle Error Counter Number of nozzle error of the parts on the feeder is displayed.
Nozzle Error % Ratio of "Nozzle Error Counter" / "Feeder Counter" is displayed.
Date
Date when the feeder was used first is displayed.
Last Update Date Date when the feeder was used last is displayed.
Specifically, this is the time when either of "Feeder Counter", "Pick
Error Counter", "Vision Error Counter", "No Parts Error Counter,”
or "Nozzle Error Counter" is counted last.
Stroke Length / Feed
Time
Distance of the tape sent by the feeder (unit: mm) is displayed.
In case of a multi stick feeder, feeding time (unit: sec) is
displayed.
Smart Exist Count
Number of feeder attachment times is displayed.
After Adjust Drive Cnt Number of times of feeder drive after adjusting by SS Tune-Up
Station is displayed. (This value cannot be initialized)
Cumulated Drive Cnt Number of times of past feeder drive is displayed. (This value
cannot be initialized)
Feeder MACS Correct
X
▲1
Feeder MACS Correction value X is displayed.
When “FEEDER MACS CORRECTION VALUE ERROR” occurs,
the error value is displayed. (This value cannot be initialized)
Feeder MACS Correct
Y
▲1
Feeder MACS Correction value Y is displayed.
When “FEEDER MACS CORRECTION VALUE ERROR” occurs,
the error value is displayed. (This value cannot be initialized)
Drive Cnt After Tape
Guide Maintenance
▲2
Number of times of feeder drive after adjusting by SS Tune-Up
Station is displayed. This works only for Auto Loading Feeder. For
any other feeders, “Drive Cnt After Tape Guide Maintenance”
always counts “0”. (This value cannot be initialized)
* Depending on timing of refresh screen, updated value might not be reflected to the screen
immediately.