P-0278-004.pdf - 第5页
MODEL HS-G300L/R 0712-002 CONT -1 目 次 CONTENTS Fig. HL ノズルストッカ 1,4 NOZZLE STOCKER 1,4 Fig. HL-1 ベース部 Base Section Fig. HL-2 ノズルストッカ Nozzle Stocker Fig. HR ノズルストッカ 2,3 NOZZLE STOCKER 2,3 Fig. HR-1 ベース部 Base Section Fig. H…
MODEL HS-G300L/R
1004-004
USING YOUR EXPLODED ILLUSTRATION
This Exploded Illustration shows the information about the parts of High Speed Nozzle
Stocker HS-G300 L/R for GXH-3 Series and is made for Parts Ordering.
You must not replace a part with a new one according to only the information of this
Exploded Illustration.
1. Inquiring
For identifi
cation of each part, numbers are placed on illustration pages. These
numbers (Key No.) again appear in the far left column of the part table joined up
with the illustration.
The number shown in the Q’
ty column of the part table represents the quantity of
certain part used in the equipment. In case of unit assembly
, however, the number
represents the quantity of certain part contained in single unit.
2. Parts Ordering
For ordering parts, some parts might not be supplied as a single item, due to the
constitution of such parts.
When ordering parts, be sure to inform us of the following details:
Model
Type
Serial No.
Fig. No.
Key No.
P
ART No.
P
ART
NAME
Quantity
[Example]
3. Miscellaneous
This Exploded Illustration is subject to change without prior notice.
All rights reserved. No part of this work covered by the copyrights hereon may be
reproduced or copied without written permission of the publisher.
'' NOTE '' is used to show the notice that is not directly related to safety.
Some of the parts shown in the Exploded Illustration could fall into the scope of your
government’s regulations on strategic products. In that case, anybody who intend to
export the product should acquire due authorization.
HS-G300L
Model Type
123456S 7890
Serial No.
Key No.139
Key No.
6300971439
PART No.
Q'ty
1
Fig. No.
Fig. HL-2
PART NAME
SENSOR, PHOTO
PREFACE-2
MODEL HS-G300L/R
0712-002
CONT-1
目 次
CONTENTS
Fig. HL
ノズルストッカ 1,4
NOZZLE STOCKER 1,4
Fig. HL-1
ベース部
Base Section
Fig. HL-2
ノズルストッカ
Nozzle Stocker
Fig. HR
ノズルストッカ 2,3
NOZZLE STOCKER 2,3
Fig. HR-1
ベース部
Base Section
Fig. HR-2
ノズルストッカ
Nozzle Stocker
G -S003-01
ノズルストッカ増設
G -S003-01 Nozzle Stocker Addition
Fig. HL
ノズルストッカ 1,4
(
G -S003-01
)
NOZZLE STOCKER 1,4
(
G -S003-01
)
Fig. HL-1
ベース部
Base Section
Fig. HL-3
ノズルストッカ２
Nozzle Stocker 2
Fig. HR
ノズルストッカ 2,3
(
G -S003-01
)
NOZZLE STOCKER 2,3
(
G -S003-01
)
Fig. HR-1
ベース部
Base Section
Fig. HR-3
ノズルストッカ２
Nozzle Stocker 2
G -S003-14
増設用基板取付本体対応
G -S003-14 Main Machine Modification
for Attaching
Added PCB
Fig. DX
架台上全体部準備
OVERALL
UPPERFRAME
PREPARATION SECTION
Fig. DX-1
I/O
ボード
L/R(Case:Block1,3) I/O Board L/R(Case:Block1,3)
Fig. DX-1 I/O
ボード
L/R(Case:Block2,4) I/O Board L/R(Case:Block2,4)
Fig. DX-4
ケーブル
(Case:Block1,3) Cable(Case:Block1,3)
Fig. DX-4
ケーブル
(Case:Block2,4) Cable(Case:Block2,4)
MEMO