TS550R-USER-GUIDE.pdf - 第11页

22 7. Ty pe: “cd :\iot” then press the “Enter” button 8. Ty pe: “ set OKI_IOT_PREFIX=MyPrefix” then press the “Enter” but ton 11 4. Touch the Check Mark icon to save and exit 5. Press the foot switch to ac tivate the “Ti…

2. Press the “BAR” icon to change pressure unit to BAR

3. Touch the X icon to save and exit

5.2.3 Manual/Purge Dispense Cycle Setting:

1. Touch the Purge icon to select the purge cycle.

The Purge icon will turn to green color.

2. Press and hold down the foot switch to activate the purge dispense cycle.

Alternately, touch and hold the Run icon on the display to activate the

purge dispense cycle.

5.2.4 Automatic Dispense Cycle Setting

1. Touch the “Timed” mode icon to set the dispense cycle in pre-set dispense

time. The icon should turn to green color.

2. Touch the Dispense icon to enter the setup screen

3. Touch the Up and Down arrows to set the desired dispense time.

Note: The minimum activation time is 0.008 second

9. Type: “set ZONEINFO=C:\iot\timezone.zip” then press the “Enter” button

10. Type: “ipconfig” then press the “Enter” button

11. Record the Server IPv4 address show in the “IPv4 Address” line on the above

screen; For this example, the Server IP address is: 172.16.40.91

This address will be entered in the controller screen later.

12. Type: “.\portal” then press the Enter button

7. Type: “cd :\iot” then press the “Enter” button

8. Type: “set OKI_IOT_PREFIX=MyPrefix” then press the “Enter” button

4. Touch the Check Mark icon to save and exit

5. Press the foot switch to activate the “Timed” dispense cycle.

Alternately, touch the run icon on the display to activate the “Timed”

dispense cycle.

Note: The unit has an “Interrupt” mode feature. In this mode, the

“Timed” dispense cycle can be disrupted if the foot switch is released and

resumed when the Foot Switch is depressed again.

6. Touch the “Interrupt” icon to activate “Interrupt” mode. The icon should

turn to green color.

5.2.5 Teach Mode Setting

In the teach mode, the dispense time will be accumulated as long as the

foot switch is depressed. This is helpful in determining the required

dispense time when the dispense output is known.

1. Touch the “Teach” icon to enter the teach mode

2. Touch the “Time Reset” icon to set timer to zero

3. Press and hold down the foot switch, the dispense time will be accumulated

4. Release the foot switch when the desired amount of fluid has dispensed

5. Touch the “Timed” icon to transfer the accumulated dispense time to

“Timed” mode

6. The unit is now set to repeat this “Timed” cycle

5.2.6 To run in Continous Mode

The controller can be setup to repeat the run continuously.

1. Touch the Setup icon to enter the setup screen

2. Touch the “Run Method” icon

3. Enter the delay time (ex. 5000 ms)

4. Touch the “Countinous Run” icon

5. Touch the Check Mark icon to save

6. Touch the X icon to exit

The screen will look similarly to the screen below:

Note: If the controller is set to activate memory cell 1 and the delay time is

set at 5000 ms, the controller will activate memory 1 continuously with

5000 ms delay between each activation.

6. INTERNET of Thing (IoT)

6.1 Setup webserver on the computer

1. Go to Techcon Website (www.techconsystems.com) and download the

following files to your computer:

a. The “portal.exe” file

b. The “timezone.zip” file

2. Create a new folder and name “IoT” or any desired name

3. Copy the “portal.exe” file and the “timezone.zip” file in the “IoT” folder

4. Click on the “Windows” start icon

5. Type: “cmd” in the box (as show below)

6. Press the “Enter” button

The screen should appear as shown below