00192419-02.pdf - 第52页

52

100%1 / 60
51
Open the horizontal tensioners (item 11)
Pull the two actuating tubes (item 6) towards you at the same time and lift
up the bracket (item 7) to lock the raised component table bed in its top
end position.
Hold down the button (item 5) for raising the component table bed (item 4)
until the component table bed reaches its top end position.
Unplug the component table power cable (item 2).
Unplug the component table control cable (item 1).
Disconnect the compressed air supply (item 3).
Remove the component table.
Docking the component table
WARNING
Check that the placement head is outside the range of the component
table.
CAUTION
When docking the component table, ensure that the table bed is in its top
end position and the bracket (item 7) is folded up.
Cut off the empty tapes for the feeder modules.
Make sure that the contact surface (item 10) for the component table bed
is clean.
CAREFULLY push the component table into the placement system.
Connect the compressed air supply (item 3).
Plug in the control cable (item 1).
Plug in the power cable (item 2) for the component table.
Pull the two actuating tubes (item 6) towards you at the same time and
then lower the bracket (item 7) in order to be able to lower the component
table bed.
Check that the centEring holes in the component table bed lie precisely
over the centering pins of the placement system.
Hold down the button (item 5) until the component table bed reaches its
top end position.
Release the button and the component table bed will descend.
Ensure that the centring pins engage in the centring holes in the compo-
nent table bed and that the component table bed is fully lowered.
Fold up the bracket (item 7) of the component table.
Lock the two horizontal tensioners (item 11).
Close the side screens and protective cover.
Press the Start button to start the placement system.
52
53
Index
Symbols
#E
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 30
A
Abbreviations
. . . . . . . . . . . . . . . . . . . . . . . . 5
Abort processing PCB
. . . . . . . . . . . . . . . . 17
Actual
. . . . . . . . . . . . . . . . . . . . . . .40, 41, 42
Actuate clamping
. . . . . . . . . . . . . . . . . . . . 43
Actuate dp axis
. . . . . . . . . . . . . . . . . . . . . . 36
Actuate stopper
. . . . . . . . . . . . . . . . . . . . . 43
Areas of placement station
. . . . . . . . . . . . . 10
B
Barcode comparison
. . . . . . . . . . . . . . . . . 27
BC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
BE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Buttons or icons
. . . . . . . . . . . . . . . . . . . . . 24
C
Cmp
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CmpName
. . . . . . . . . . . . . . . . . . . . . . . . . 26
CO
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CO-BC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Component barcode
. . . . . . . . . . . . . . . . . . 26
Component barcode reader (option)
. . . . . . 7
Component counter
. . . . . . . . . . . . . . . . . . . 7
Component name
. . . . . . . . . . . . . . . . . . . . 30
Confirm all
. . . . . . . . . . . . . . . . . . . . . . . . . 39
Confirm all magazines
. . . . . . . . . . . . . 41, 42
Confirm each change
. . . . . . . . . . . . . . . . . 38
Confirm one magazine
. . . . . . . . . . . . .40, 42
Confirm one nozzle
. . . . . . . . . . . . . . . . . . 42
Continue processing
. . . . . . . . . . . . . . . 11, 14
Conveyor belt, high speed
. . . . . . . . . . . . . 43
Conveyor track 1
. . . . . . . . . . . . . . . . . . . . 10
Conveyor track 2
. . . . . . . . . . . . . . . . . . . . 10
Cover
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
D
DEV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 30
Display empty tracks
with component verification
. . . . . . . . . . 32
without component verification
. . . . . . . 32
Display for the machine’s current
operating mode
. . . . . . . . . . . . . . . . . . 15
Displays and controls
. . . . . . . . . . . . . . . . . . 7
description
. . . . . . . . . . . . . . . . . . . . . . . . 7
Division
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Docking and undocking the CO table
. . . . . 49
E
Emergency stop mushroom-head
push-button
. . . . . . . . . . . . . . . . . . . . . 11
Emergency-stop mushroom-head
push-button
. . . . . . . . . . . . . . . . . . . 6, 11
Enter Password
. . . . . . . . . . . . . . . . . . . . . 21
Error counter
. . . . . . . . . . . . . . . . . . . . . . . 30
Error information, line
. . . . . . . . . . . . . . . . . 14
Error number
. . . . . . . . . . . . . . . . . . . . . . . .30
F
Fault list with title bar
. . . . . . . . . . . . . . . . . .30
Fiducial errors
. . . . . . . . . . . . . . . . . . . . . . .48
Flowchart
„Switching on the SIPLACE line“
. . . . .59
Forced air on/off
. . . . . . . . . . . . . . . . . . . . .36
G
Gantry reference run
. . . . . . . . . . . . . . . . . .35
Garage
. . . . . . . . . . . . . . . . . . . . . . . . . . . .41
GEM status display
. . . . . . . . . . . . . . . . . . .15
General errors
. . . . . . . . . . . . . . . . . . . . . . .30
General operating statuses
. . . . . . . . . . . . . .8
GF
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
GF no.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Go to service position
. . . . . . . . . . . . . . . . .35
Go to set-up position
. . . . . . . . . . . . . . . . . .35
Go to waiting pos’n
. . . . . . . . . . . . . . . . . . .35
Go to zero pulse
. . . . . . . . . . . . . . . . . . . . .35
Guard
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
H
Head reference run
. . . . . . . . . . . . . . . . . . .36
Holding circuit
. . . . . . . . . . . . . . . . . . . . . . .37
Hot key
. . . . . . . . . . . . . . . . . . . . . . . . . . . .12
I
Icon
General errors menu
. . . . . . . . . . . . . . .30
Machine errors menu
. . . . . . . . . . . . . . .30
Track errors menu
. . . . . . . . . . . . . . . . .30
Transport errors menu
. . . . . . . . . . . . . .30
Icons
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
meaning of the
. . . . . . . . . . . . . . . . . . . .14
Input box
. . . . . . . . . . . . . . . . . . . . . . . . . . .19
Input conveyor
. . . . . . . . . . . . . . . . . . . . . . .10
K
Key switch
. . . . . . . . . . . . . . . . . . . . . . . . . . .6
Keyboard with integral trackball
. . . . . . . . . .7
Keyboard with integrated mouse
. . . . . . . . .12
L
Level
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Line computer
shutdown
. . . . . . . . . . . . . . . . . . . . . . . .22
switching off
. . . . . . . . . . . . . . . . . . . . . .22
List field
. . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Location
. . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Location 1
. . . . . . . . . . . . . . . . . . . . . . . . . .10
Location 3
. . . . . . . . . . . . . . . . . . . . . . . . . .10
Location number
. . . . . . . . . . . . . . . . . . . . .26
Lock open/closed
. . . . . . . . . . . . . . . . 40, 41
LP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5