3OM-1011-001.pdf - 第183页
0305-001 2-138 Tg0859-PM-ER Error Code Display A Display B 3. T rouble Shooting after Error Display (Cause 1) This is the device's self-diagnostic message. (Reset Procedure in the case of Cause 1) Reset Procedure (1…
0305-001 2-137 Tg0859-PM-ER
Error Code Display A Display B
3. Trouble Shooting after Error Display
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Follow the steps below to reset the machine to the normal condition.
(2) When the [RESET] botton is pressed, the following display appears on the screen.
(3) Press the [WARM START] button.
The following “WARM START” display appears. After zeroing all the devices, perform the
warm start operation to complete the unfinished P.C.B.
Refer to “4.3 Warm Start of Section 3 in Volume 1” for details.
Fig. 3B5
Fig. 3B6
0305-001 2-138 Tg0859-PM-ER
Error Code Display A Display B
3. Trouble Shooting after Error Display
(Cause 1) This is the device's self-diagnostic message.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [CLEAR ALARM] key and the buzzer stops sounding.
(2) Press [SYS CLR] button.
(3) Press the [ZERO] button to return all the axes to their original positions.
(4) Re-start.
(5) If the device can't be re-started, contact our service personnel.
6C 04 01 INTERNAL DATA ERROR INTERNAL DATA UNUSUALLY OCCURRED.
6C 04 02 INTERNAL DATA ERROR THERE WAS A FAILURE INCLUDING READING OF
TEXT DATA.
(Cause 1) There is a possibility that text data are not installed or damaged.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [CLEAR ALARM] key and the buzzer stops sounding.
(2) Re-install CPU1 program.
(3) Press the [ZERO] button to return all the axes to their original positions.
(4) Re-start.
(5) If the device can't be re-started, contact our service personnel.
0305-001 2-139 Tg0859-PM-ER
Error Code Display A Display B
3. Trouble Shooting after Error Display
6D 01 04 JIG COMPONENT JIG COMPONENT NOT PLACED ON BACKLIGHT
PLATE.
(Cause 1) This is the device’s self-diagnostic message.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [ZERO] button to return all the axes to their original positions.
(2) Re-start.
(3) If the device can’t be re-started, contact our service personnel.
6D 01 03 JIG COMPONENT JIG COMPONENT NOT PICKED UP FROM BACK-
LIGHT PLATE.
(Cause 1) This is the device’s self-diagnostic message.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [ZERO] button to return all the axes to their original positions.
(2) Re-start.
(3) If the device can’t be re-started, contact our service personnel.
6D 01 02 JIG COMPONENT JIG COMPONENT NOT RE-STORED IN STOCKER.
(Cause 1) This is the device’s self-diagnostic message.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [ZERO] button to return all the axes to their original positions.
(2) Re-start.
(3) If the device can’t be re-started, contact our service personnel.
6D 01 01 JIG COMPONENT JIG COMPONENT NOT PICKED UP FROM STOCKER.
(Cause 1) This is the device’s self-diagnostic message.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [ZERO] button to return all the axes to their original positions.
(2) Re-start.
(3) If the device can’t be re-started, contact our service personnel.