IPC-A-610国际标准中英文对照.pdf - 第3页

IPC-A-610 国际标准中英文对照

Table of Contents(cont.)目录(续)

3.1 Electrical Overstress (EOS) Damage 4.2.2 Excess Solder....................35

Prevention.........................16 多锡

电子过压力（EOS）破坏预防 4.2.3 Threaded Fasteners...............36

3 .2 Electrostatic Discharge (ESD) 紧固螺钉

Damage Prevention.................18 4.2.3.1 Minimum Torque for Electrical

静电释放损坏的预防 Connections.....................38

3.2.1 Warning Labels...................21 电气连接的最小扭力

警告标签 4.2.3.2 Wires...........................39

3.2.2 Protective Materials.............22 导线

保护性材料 4.2.3.3 High Voltage Applications.......41

3.3 EOS/ESD Safe Workstation/EPA.......24 高压应用

安全工作站／静电保护区（EPA） 4.2.4 Component Installation..........42

3.4 Handling...........................27 组件安装

操作 4.2.4.1 High Power......................42

3.4.1 Guidelines.......................27 高功率

指南 4.2.4.2 Hole Obstruction of Solder Fill.44

3.4.2 Physical Damage..................28 孔塞满锡

物理损坏

3.4.3 Contamination....................28 4.3 Swaged Hardware.....................45

污染锻造部件

3.4.4 Electronic Assemblies............28 4.3.1 Flared Flange...................46

电子组装品翻边凸轮

3.4.5 After Soldering .................29 4.3.1.1 Controlled Split................48

焊接后受控裂缝

3.4.6 Gloves and Finger Cots...........30 4.3.2 Flat Flange-Fused-in-place......50

手套和指套平凸轮

4 Mechanical Assembly..................31 4.3.3 Terminals.......................53

机械装配终端

4.1 Hardware

..........................33 4.4 Component Mounting..................55

部件组件安装

4.2 Hardware Mounting..................34 4.4.1 Mounting Clips...................56

部件安装安装夹片

4.2.1 Electrical Clearance.............34 4.4.2 Adhesive Bonding-Non-Elevated

电气间隙 Components......................58

粘合剂—非悬空组件

0-2

IPC-A-610 国际标准中英文对照

Table of Contents(cont.)目录(续)

4.4.3 Adhesive Bonding-Elevated 5.1.2 Vertical..........................86

Components.....................62 垂直

粘合—悬空组件 5.2 Mounting............................87

4.4.4 Wire Hold Down.................64 安装

压线器 5.2.1 Horizontal-Axial Leaded-

4.4.5 Cable Ties,Tie Wraps,Spot Ties..65 Supported Holes...................87

电缆的捆绑、束线带、点结水平—轴向引脚—有支撑孔

4.4.6 Lacing.........................68 5.2.2 Horizontal-Axial Leaded-

索系 Unsupported Holes...............88

4.4.7 Wire Dress for Terminations to 安装-水平-轴向引脚-无支撑的孔

Connectors Without Strain/Stress 5.2.3 Horizontal-Radial Leaded .......90

Relief.........................69 水平—径向引脚

端子与连接器之间线材外被的张力和应力 5.2.4 Vertical-Axial Leaded-

4.5 Connectors, Handles, Extractors....70 Supported Holes................91

连接器—把手—抽取器垂直—轴向引脚—有支撑的孔

4.6 Heat sink........................71 5.2.5 Vertical-Axial Leaded-

散热片 Unsupported Holes..............93

4.6.1 Insulators and Thermal Compounds.73 垂直-轴对称引脚-无支撑物的孔

绝缘体和热敏混合物 5.2.6 Vertical-Radial Leaded..........94

4.6.2 Contact..........................74 直——径向引脚

接触片 5.2.6.1 Component Mounting Spacers

4.7 Terminals-Edge Clip................75 Spacers.....................95

终端——边缘夹子组件安装隔离器

4.8 Connector Pins.....................76 5.2.6.2 Component Meniscus..............97

连接器针脚凹型组件

4.8.1 Edge Connector Pins..............77 5.2.7 Wire/Lead Termination-

连接器边缘针脚 Printed Board...................98

4.8.2 Fit Pins.........................77 导线/引脚末端—印刷线路板

压针 5.2.7.1 Protrusion-Straight and

5. Component Installation Location/ partially Clinched Leads........98

Orientation.......................81 露出长度-直形和部分弯曲引脚

组件贴装的位置和方向 5.2.7.2 Clinched........................100

5.1 Orientation.......................85 弯曲

方向

5.1.1 Horizontal....................85

水平

0-3

IPC-A-610 国际标准中英文对照

Table of Contents(cont.)目录(续)

5.2.8 Dual-in-Line Pack (DIP)/ Single-in- 5.1.1 Turrets and Straight Pins.....119

Line pack(SIP) Pins and Sockets....103 塔状和直形针脚

双列式（DIP）封装/单列式（SIP）封装 5.1.2 Bifurcated Terminals..........121

针脚和插槽分叉接线端

5.2.9 Connectors........................105 5.5.1.3 Pierced/Perforated Terminals 124

连接器穿孔/穿洞接线端

5.2.10 Leads Crossing Conductors.........107

引脚与线路交叉 5.5.1.4 Hook Terminals..............126

5.3 Lead Forming.........................108 钩型接线端

引脚形状 5.5.1.5 Series Connected Terminals..128

5.3.1 Bends.............................108 并列接线端组

弯曲

5.3.2 Stress Relief.....................110 5.5.1.6 AWG 30 and Smaller Diameter

应力消除 Wires....................130

5.3.2.1 Supported Holes...................110 AWG30和更小直径导线

有支撑物的孔 5.5.1.7 Staked Wires/Components.....131

5.3.2.2 Unsupported Holes.................112 有支撑的导线/组件

无支撑物的孔 5.5.2 Solder Cups.................133

5.3.2.3 Terminals.........................113 焊帽

接线端 5.5.3 Stress Relief Lead/Wire

5.4 Damage................................114 Bend.......................134

损坏引脚/导线弯曲应力的消除

5.4.1 Lead..............................114 5.5.4 Service Loops...............136

引脚捆绑环

5.4.2 DIP and SOIC......................115 5.5.5 Lead/Wire Placement.........137

DIP 和 SOIC 引脚/导线安插

5.4.3 Axial Lead and Glass Body/Seal....117 5.6 Insulation......................138

轴向引脚和玻璃本体/封装绝缘

5.4.4 Radial (Two Lead).................118 5.6.1 Clearance...................138

放射状（双引脚）间隙

5.5 Terminals.............................119 5.6.2 Damage......................139

接线端损坏

5.5.1 Wrap..............................119 5.6.3 Flexible Sleeve.............141

缠绕软套筒

0-4