00194335-02.pdf - 第20页
2 Retrofit instructions Coplanarity module - SIPLACE HF ser ies Coplanarity module 10/2004 Edition 20 2.3 Safety instructions W ARNING The safet y instruction s from the “Operationa l safety” chapter of th e user manua l…
Coplanarity module 2 Retrofit instructions Coplanarity module - SIPLACE HF series
10/2004 Edition
19
2 Retrofit instructions
Coplanarity module - SIPLACE HF series
2.1 Requirements
The coplanarity module can only be used with software version 505.01 incl. Patch or later. 2
With the SIPLACE HF, the new reject bin (item no.: 03003047-02) and its frame (item no.:
03003048-03) will also have to be installed. 2
From May 2004, these parts will be supplied as standard, and will thus be fitted at the factory. 2
Check whether these parts are already fitted in the machine and retrofit them if necessary. 2
2.2 Parts required
2.2.1 Retrofit kit (item no.:00119619-01)
2
2.2.2 Tools and consumables required
– Set of hexagon socket spanners
– Set of slotted-head screwdrivers
– TORX key size 8
– Coplanarity test plug
– Threading aid
–Cable ties
Coplanarity module (laser, processor, cable)
Item no.: 00119619-01
Mount
Item no.: 03013105-01
Additional cable for computer unit
Item no.: 03021751-01
Interface cable
Item no.: 00336796-02
Test plug
Item no.: 00337304-01
Calibrating part
Item no.: 00315365-03
Warning label (#208)
Item no.: 03009347-01
Retrofit instructions
Item no.: 00194335-01
2 Retrofit instructions Coplanarity module - SIPLACE HF series Coplanarity module
10/2004 Edition
20
2.3 Safety instructions
WARNING
The safety instructions from the “Operational safety” chapter of the user manual and servicing in-
structions take precedence over these instructions. 2
The SIPLACE placement machines are supplied with mains voltage.
Consequently parts of these systems carry dangerous voltages! This voltage is present at certain
modules inside the machine base, even when the machine is switched off at the main power
switch.
Incorrect handling of the placement machine or touching live parts of the machine can result in
death or severe injury, and considerable damage to equipment.
BEFORE starting any work, shut down the operating system correctly, then switch the machine
OFF at the main power switch and disconnect from the main power supply. In addition, the com-
pressed air supply must be switched off at the compressed air unit's main valve in the machine
base and vented by actuating the needle valve on the compressed air unit.
There is DANGER for heart pacemaker wearers in the vicinity of the linear motors, as described
in detail in the "Special safety instructions for working in the vicinity of strong magnetic fields"
section of the user manual and service manual.
Always follow the accident prevention regulations, DIN or other standards and special safety
rules applicable in your country.
Pay attention to the information concerning residual voltages in the Operational Safety chapter.
Follow the ESD regulations as described in the operational safety section of the operating
instructions.
During the retrofit, always secure the machine to prevent access by other people and to prevent
it being switched on again. The procedure is described in the “Locking the machine…” section of
the user manual.
Working with the SITEST program further increases the risk of accident.
The SITEST program must only be used by authorized and trained personnel.
2
2
2
2
2
Coplanarity module 2 Retrofit instructions Coplanarity module - SIPLACE HF series
10/2004 Edition
21
2.3.1 Safety instructions for laser units
Permission to operate components that are classified as lasers is withdrawn if
– mechanical damage to the unit is observed, or
– any work is done on the mechanical or electrical parts of the unit.
Even damaged or missing screw locking paint on laser components (e.g. cover plates, fas-
teners, adjusting potentiometer) counts as work.
– Only SIEMENS service engineers, or the machine owner's service engineers who have
been trained by SIEMENS are allowed to replace laser components.
– Repairs to laser units are carried out at the SIEMENS factory exclusively.
2
2.3.2 Definitions
2
PLEASE NOTE 2
2
2
2
Caution 2