196396 Iss 2 Nov 2015 - Semi Appendix Manual.pdf - 第28页
SERVICES REQUIRE D EXTERNAL SE RVICES 3.2 Installation Manual Chapter Issue 4, N ov 14 Pneumatic Supply The machine re quires a pneumatic supply of clean, non lubricated air whi ch should maint ain a minimum pressure 5 B…
COVERS
PRINTER COVERS
Chapter Issue 4, Nov 14 Installation Manual 2.13
5. Release the quarter-turn fastener that secures the corner panel.
6. Lift the corner panel upwards to disconnect the panel from the side panel
and the guide pins that locate the panel to the machine frame.
NOTE
Failure to assemble the front EMO switch correctly results in the EMO
circuit remaining active preventing the machine from being powered up.
Rear Corner
Panels
To remove the rear corner panels, carry out the following:
1. Remove the corresponding upper side panel (as detailed previously).
2. Release the quarter-turn fastener that secures the corner panel.
3. Lift the corner panel upwards to disconnect the panel from the side panel
and the guide pins that locate the panel to the machine frame.
4. Repeat Steps 1 to 3 for the other corner panel, if required.
Side Panels To remove the side panels, carry out the following:
1. Remove both corresponding corner panels (as detailed previously).
Front Corner
Panel Quarter-
Turn Fastener
Front Corner
Panel Quarter-
Turn Fastener
Rear Corner
Panel Quarter-
Turn Fastener
Rear Corner
Panel Quarter-
Turn Fastener
SERVICES REQUIRED
EXTERNAL SERVICES
3.2 Installation Manual Chapter Issue 4, Nov 14
Pneumatic Supply The machine requires a pneumatic supply of clean, non lubricated air which
should maintain a minimum pressure 5 Bar and a maximum of 8 Bar.
The air should be to ISO 8573.1 standard, quality class 2.3.3, where:
• 2 dirt = 1 micron
• 3 water = -20°C pressure dewpoint
• 3 oil = 1mg/m3
Electrical Supply The factory mains supply for the machine is routed through the front panel
mounted mains isolator switch to the M39 EMO enclosure. If both EMO push
button switches are de-activated and the Start button has been pressed mains
voltage is applied to the M37 power supply enclosure. From the enclosure
various low voltages are distributed throughout the machine.
Figure 3-1 Mains Electrical Supply
The machine operates on 100V to 240V + 10% 50/60Hz single phase ac mains,
current rating 10A or 2.4Kw.
NOTE
The voltage selector of the VF35i vacuum filtration unit needs to be set to the
factory mains supply. This is carried out in the Machine Preparation Chapter
later in this manual.
ASM recommends a power supply capacity of 2.4KVA or greater.
From Factory
Mains Supply
Mains Isolator
Switch
M37 Power Supply Enclosure
M39 EMO Enclosure
SERVICES REQUIRED
EXTERNAL SERVICES
Chapter Issue 4, Nov 14 Installation Manual 3.3
ASM requires additional machine supply protection with the fitment of an
external double pole circuit breaker conforming to national, federal or local
legislation. ASM recommends that the external circuit breaker is fitted near the
DEK printer and within easy reach of the operator. Use the following table to
ensure the recommended circuit breaker is used:
NOTE
An over current circuit breaker protects the machines internal wiring and
components from overheating or catching fire during fault conditions. Under no
circumstances must a circuit breaker of value greater than 25 Amps be fitted.
Equipment If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
This equipment should be used in accordance with the operating instructions.
ASM absolves itself of all responsibility if the machine is not used within its
operating envelope or for it’s intended purpose.
Circuit Breakers The M37 Power Supply Enclosure has circuit breakers on the front and rear
panels of the enclosure.
Front Panel Circuit
Breakers
Voltage Value of Wall Mounted Circuit Breaker
(without Internal Vacuum Unit)
Value of Wall Mounted Circuit Breaker
(with Internal Vacuum Unit)
115V 10 Amp 25 Amp
230V 4/6 Amp 13/16 Amp
CCT Breaker Current Rating CCT Breaker Function
CB32 10A +42V or +48V Servo DC Supply
CB33 10A Mains Supply PC and Monitor
CB34 16A Mains Supply Internal Vac Pump
CB32
CB33
CB34
10A
Type C
10A
Type C
16A
Type C
Part View of Front Panel