WPC an:on SIPLACE SX1:SX2 Montageanleitung : Assembly Instructions.pdf - 第46页
1 Introduction 46 Mo nt ag ea nl ei tu ng / A ss em bl y In st ru ct io ns W PC a n/ on S IP LA CE S X1 /S X2 - 0 3/ 20 25 1.1.2 Safety instructions for working with strong magnetic fields DANGER Strong permanent magneti…
1 Introduction
Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025 45
1 Introduction
This manual describes the replacement of the standard feed device with the WPC5 feed device on SI-
PLACE® SX1/SX2 machines. (WPC = Waffle Pack Changer).
1.1 Safety instructions
DANGER
Nonobservance of these safety instructions may cause injury to personnel and damage to the
machine!
► Please observe the safety instructions in the user manual of the relevant machine for all
work!
1.1.1 Conventions for the use of safety instructions and symbols
Safety information
This document contains notes that must be observed to guarantee your personal safety and to avoid
damage to equipment. These notes are highlighted by warning triangles and are indicated as follows
according to the level of risk:
DANGER
Definition
For the purposes of this document, this indicates that fatal or severe injuries or considerable damage
to property will occur if this hazard warning is not observed.
WARNING
Definition
For the purposes of this document, this indicates that fatal or severe injuries or considerable damage
to equipment may occur if these warning instructions are not followed.
CAUTION
Definition
For the purposes of this document, this indicates that minor injuries or damage to property may occur
if this caution is not observed.
NOTICE
Definition
For the purposes of this document, this note provides information about the product or indicates a
part of the document that requires particular attention.
Symbols
Example Description
Next This typeface marks controls and interface elements in the software.
► This symbol indicates actions that have to be performed by the operator.
[01234567‑xx] Article numbers are indicated by square brackets.
1 Introduction
46 Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025
1.1.2 Safety instructions for working with strong magnetic fields
DANGER
Strong permanent magnetic fields
Fatal hazard: persons with active implants (e.g. pacemakers, defibrillators, insulin pumps, etc.) are at
risk from strong permanent magnetic fields inside the machine.
Persons at risk should avoid the immediate vicinity of the machine.
CAUTION
Danger of crushing
Danger of crushing for persons with passive metal implants (e.g. plates, screws).
► Do not reach or lean over into the machine when the covers are open.
► Do not bring any metal objects into the danger area.
CAUTION
Strong permanent magnetic fields
There is a risk that the strong magnetic fields could corrupt data on data media or check cards.
► Keep sensitive data media away from the permanent magnets.
1.1.3 Safety instructions for the power supply (without SMPS)
NOTICE
Validity
This section applies to the following machine types (without SMPS power supply):
► SIPLACE DX1/DX2 and SX1/SX2 up to serial no. Mxxxx
DANGER
Hazardous voltages!
The machine is supplied with 3x400V~ (or 3x204V~ / 3 x 220V~ / 3 x 230V~ / 3 x 380V~ /
3x415V~) ± 5%, 50/60Hz mains voltages.
► Observe the safety instructions in the user manual during all service work!
► Before you start working on the power supply, check it for absence of voltage and observe the
waiting times!
► The covers of the power supply unit must ONLY be opened by appropriately qualified and
trained personnel.
●
This means that some parts of the system carry potentially lethal voltages – even when switched
off at the main power switch.
●
Incorrect handling of the placement system can therefore result in fatal injuries, severe injuries or
considerable damage to equipment.
●
Measurements and maintenance work must always be carried out by appropriately qualified per-
sonnel.
●
Always follow the applicable accident prevention and DIN regulations (particularly DIN EN 60
204, part 1) or the regulations specific to your country.
●
Before starting any maintenance work, switch the machine off at the main switch and disconnect
it from the main power supply.
●
Always secure the machine against unauthorized reactivation. If these instructions are not fol-
lowed, you may be able to touch live parts, which could result in fatal or severe injuries.
1 Introduction
Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025 47
Maintaining, installing or removing assemblies
► End all placement operations on the machine.
► Shut down the Windows operating system correctly, otherwise problems may occur when
restarting or data may be lost.
► Switch the machine off at the main switch.
► Disconnect the machine from the main power supply.
► Switch off the machine and attach warning signs to indicate that service work is in progress.