WPC an:on SIPLACE SX1:SX2 Montageanleitung : Assembly Instructions.pdf - 第64页
3 Setting up and Commissioning 64 Mo nt ag ea nl ei tu ng / A ss em bl y In st ru ct io ns W PC a n/ on S IP LA CE S X1 /S X2 - 0 3/ 20 25 Fig.18: Mounting the waste tape chute ► Install the waste tape slide. For more i…
3 Setting up and Commissioning
Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025 63
Fig.16: Mounting tool (example of X-Series shown)
1. Mounting tool
2. Eyelet
3. Fastening screws
4. WPC5 feed device
► Attach the fit-up aid to the component trol-
ley feed device.
► Hook the feed device up to the lifting
device by its eyelet.
► Lift the feed device with the lifting device
and move this carefully into the machine
but do not lower it fully yet.
► Carefully thread the cable tree into the machine frame, on the right.
► Lower the feed device onto the contact surface and remove the lifting device.
► Dismantle the lifting device from the feed device.
► Hold the bracket from below, against the feed device and screw this tight with three screws on
each side. Make sure that the nibs on the brackets fit exactly into the recesses in the feed device.
► To the right of the feed device in sector2 or4 you will find the compressed air hose "COT1/2".
Run this through the base, behind the feed device, and up.
► Connect the hose to the Y distributor of the feed device. This is located under the nozzle reject
bin holder.
► Restore all electrical connections to and from the feed device.
Fig.17: Grounding the cable
► Earth the feed device by connecting the
cable to the machine base as shown.
► Fit the bracket for checking the table height onto the right-hand side. Make sure that the nib is po-
sitioned correctly.
The bracket on the left hand side is not needed.
For more information about this, read section 5.1.1 "Downholder" [}69].
► Tighten the screws fastening the angle plates on the left and right.
► Fit the cutter by following the instructions in reverse order.
► Fit the right-hand nozzle changer by following the instructions in reverse order. The left-hand
nozzle changer is not needed.
3 Setting up and Commissioning
64 Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025
Fig.18: Mounting the waste tape chute
► Install the waste tape slide. For more infor-
mation, read section 5.1.4 "Replacing the
Waste Tape Chute" [}78].
► Move the WPC5 into the machine (see also 4.1 "Docking the WPC5/WPC6" [}65]).
CAUTION
Camera
Take care not to damage the stationary camera.
► Plug the WPC5 into the machine.
► Connect the WPC5 safety chain to the machine.
► Crank the WPC5 down.
► Switch on the WPC/WPCs and the machine.
NOTICE
Start up sequence with two WPCs
In case of two WPCs on one machine the start up sequence has to be observed. Otherwise some er-
rors (CAN switch errors) may occur.
► Always switch on the WPCs first and then the machine.
► On machines of type SX1/SX2 as well as DX1/DX2 with two WPCs, both WPCs must be
switched on simultaneously with the machine (within 12 sec.).
If not, the CAN switch switches into the "error" state.
► Move the changeover table into the machine.
► Perform a function check.
4 Operator Tasks
Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025 65
4 Operator Tasks
4.1 Docking the WPC5/WPC6
When installing and removing the WPC5/WPC6, make sure that the arms of the feed axis do not hit
any parts (e.g. stationary cameras etc.).
► If the WPC5/WPC6 is not yet standing on its wheels, fasten the hexagonal shaft (crank handle) to
the lifting mechanism and turn in a clockwise direction, to lift the WPC5/WPC6.
► Stop turning when you have enough room to dock the WPC5/WPC6 onto the machine.
► Open the machine cover on the relevant location.
► If there is a height limiter present in the WPC5/WPC6 location, this needs to be turned over and
fixed into place upside down. Make sure that the height limiter does not touch the cover plate. To
do this, loosen the three screws fastening the height limiter and fit it into the same place upside
down (with two fastening screws).
► Move the WPC5/WPC6 into the location and connect the energy and data supply cable. Make
sure that the arms of the feed axis do not collide with any machine parts.
► Lower the WPC5/WPC6 until it is standing on its feet. Turn the crank handle on the lifting mech-
anism until the wheels are about 1 cm above the ground.
Aligning the WPC5/WPC6
Fig.19: Checking the position of WPC5/WPC6
1. Circular spirit level
► Check the position of the WPC5/WPC6
with the help of the integrated spirit level
(1), which is between the two rails of the
feeder axis.
NOTICE!
The cover on the feed axis arms is not
shown in the diagram.
.
Fig.20: Adjustable feet
1. Foot with 30 mm nut
2. 36 mm locknut
3. Hexagonal shaft (crank handle)
► If the WPC5/WPC6 is not level, use a 30
mm and 36 mm open-ended wrench to ad-
just the feet in turn, until more than half of
the bubble is in the circle of the spirit level.