WPC an:on SIPLACE SX1:SX2 Montageanleitung : Assembly Instructions.pdf - 第56页
1 Introduction 56 Mo nt ag ea nl ei tu ng / A ss em bl y In st ru ct io ns W PC a n/ on S IP LA CE S X1 /S X2 - 0 3/ 20 25 1.4.5 Release History Document WPC5 on the SIPLACE SX1/SX2 Assembly Instructions Edition Changes …
1 Introduction
Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025 55
1.4.3.5 Dispatching ESD modules
► Always store modules and components in conductive packaging (e.g. metallized plastic bags or
metal sleeves) and dispatch them in conductive packaging.
► If the packaging is not conductive, place the modules in a conductive envelope before packaging.
Use conductive expanded rubber, ESD bags, domestic aluminum foil or paper, for example.
NEVER use plastic bags or film.
► If the module has integral batteries, ensure that the conductive packaging does not touch or short
circuit the battery terminals and, if necessary, first cover the terminals with insulating tape or
material.
1.4.4 Validity of Document
This document contains instructions for the installation of WPC modules.
The work described in this manual is largely identical for all WPC types:
●
If the work required for specific machines should differ from the standard procedure, this will be
indicated with reference to the machine number, series and delivery state.
●
Diagrams should be seen as examples e.g. the diagram of a SIPLACE WPC5 or a different paint
finish does not mean that the following information only applies to the type shown.
1 Introduction
56 Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025
1.4.5 Release History
Document
WPC5 on the SIPLACE SX1/SX2
Assembly Instructions
Edition Changes
06/2009 Initial release
12/2011 Revision and supplements
03/2014 Adjustments and supplements:
●
Dimensions and weight: Supplements for component heights of the different
WPC types
●
Parts, Equipment and Tools
●
Formal adjustments
●
Installation of CAN nodes
●
Start up sequence with two WPCs
●
Minor corrections and supplements
01/2016 Amendments and supplements:
●
CAN bus terminator for CO table
03/2025
●
Chapter "Excerpts from the Service Manual":
– Waste Type Chute and Compressed Air Supply added
– Downholder updated
●
Rebranding
●
Minor changes
1.5 Staff qualifications and training
Qualified or adequately trained personnel means that these people are familiar with the setting up,
operation and maintenance of the machine and the add-on devices and are suitably qualified, e.g.:
●
Have been trained, instructed or authorized to switch on and off, isolate, earth and identify elec-
trical circuits and system components in accordance with normal safety standards.
●
Have been trained or instructed in the upkeep and use of appropriate safety equipment in accor-
dance with normal safety standards.
2 Brief description
Montageanleitung / Assembly Instructions WPC an/on SIPLACE SX1/SX2 - 03/2025 57
2 Brief description
2.1 Overview of WPC5/WPC6
Fig.6: Overview of WPC
1. SIPLACE SX1/SX2
2. WPC6
3. Non-Stop Module (only WPC6)
4. 30-track changeover table
2.1.1 Overview of the Modules
Fig.7: Overview of the modules
1. Protective door
2. Non-Stop Module (only WPC6)
3. EMERGENCY STOP button
4. Main switch
5. Protective covers on the power supply
6. Crank handle for lifting or lowering the trol-
ley carriage
7. Protective covers on the lifting mechanism
(tower)
8. Feed axis with waffle pack tray carrier
9. Cover over the feed axis drive