00197961-01_UM_JTF-MW_on_SIPLACE_E_en_FINAL.pdf - 第42页
Tasks on the Machine Controls and Displays on the Feeder Co ntrol Panel 42 User Manual JTF-MW on SIPLACE E The precise functions ar e described below: Index 1 (10) and index 2 (5) Index 1 (10) and 2 (5) only trigger a tr…
Tasks on the Machine
Powering up the Feeder
User Manual JTF-MW on SIPLACE E 41
5
5 Tasks on the Machine
Tasks on the Machine
This chapter describes how to operate the JTF-MW in the production process.
5.1
5.1 Powering up the Feeder
Powering up the Feeder
After connecting the feeder to the machine (see "4.6.2 Connecting the JTF-MW to the Machine" [➙35]),
the feeder initializes by driving the magazine upwards.
If no magazine is detected, the elevator drives down and switches to stands by.
If a magazine is detected, the first tray is positioned on the feeding level.
Now the feeder is ready to accept commands.
5.2
5.2 Controls and Displays on the Feeder Control Panel
Controls and Displays on the Feeder Control Panel
The diagram shows the control panel on the feeder.
The functions "Index, Inhibit and Elevator Down" are regulated by the controller.
The functions "Stop and Reset" are an electronic stopping function for the pneumatic system. If you
press the stop button, the pneumatic system immediately switches off and the motors will stop. The sta-
tus is read by the controller but not regulated by it.
Tasks on the Machine
Controls and Displays on the Feeder Control Panel
42 User Manual JTF-MW on SIPLACE E
The precise functions are described below:
Index 1 (10) and index 2 (5)
Index 1 (10) and 2 (5) only trigger a tray changeover if
they are both pressed (series connection). The next tray
in the series is moved into the magazine. A connection to
the serial interface is needed for the various feeder com-
mands.
This function is disabled in production mode.
Stop (9)
If you press the stop button (9), the pneumatic system im-
mediately switches off and the motors will stop. The stop
button supports the stopping function of the pneumatics
system. A signal is sent to the host.
The "Stop and Reset" functions can not be switched off
by the production mode.
Reset (8)
The reset button (8) resets the feeder after a stop condi-
tion. A signal is sent to the host.
The "Stop and Reset" functions can not be switched off
by the production mode.
Inhibit (7)
The inhibit button (7) locks the remote control for the
SIPLACE JTF-MW. The feeder does not receive any con-
trol commands from the host. This lock is released when
the button is pressed again.
This function is disabled in production mode.
Elevator down (6)
This function allows you to change the trays in the maga-
zine without stopping production. The magazine moves
down and the current tray in the pick position remains
clamped and the ready LED (green) continues to shine.
► As soon as the lift stops at the bottom, the door can
be opened and the trays can be changed.
► Open the door once the lift has reached the bottom.
► Leave the empty slot (for the tray currently used in the
pick position) empty.
This function is disabled in production mode.
Tasks on the Machine
Loading and Unloading Trays
User Manual JTF-MW on SIPLACE E 43
5.3
5.3 Loading and Unloading Trays
Loading and Unloading Trays
The tray magazine is installed in the JTF-MW tower.
LED indicators
Green LED – READY (1)
LED on Shows that a tray was successfully moved to the pick position and
is now ready for components to be removed from the tray (or for it
to be loaded). The LED also shows that a ready signal has been
sent to the host. As soon as the tray leaves the pick position, the
LED will extinguish.
LED off Not ready for loading or unloading or tray changeover.
Orange LED – Stop/Error (2)
LED on Stop condition. For example, occurs after stop button was pressed.
LED flashes Error condition. An error occurred during the tray changeover.
LED off Normal mode
Yellow LED – Inhibit (3)
LED on The yellow LED shows a lock. The feeder will not receive any tray
changeover commands, neither via the remote control nor manual-
ly.
LED off Normal mode.
Blue LED – Full/Empty (4) If the next tray is manually queried after the last tray in the maga-
zine (slot with the highest number), the blue LED will show EMPTY.
This also occurs when there is no magazine inserted.
► Move the magazine down to the bottom limit (1).