DR_A_MANUAL.pdf - 第4页

A ø B ø C560-001 C560-002 C560-003 C560-004 C560-009 C560-014 Changing Tips Th is ope ratio n sho uld be d one w hile th e tip is h ot and at a m inim um temp eratu re of 250°C, so that any ti n lef t ins ide is s till m…

100%1 / 20
Connection
Desoldering Iron
Ref. DR560-A
Tip
Ref. C560003
to desoldering module
to stand
Suction Filter
Ref. 0821830
Supplied with desoldering module
Desoldering process
Use a tip with a larger diameter than the pad to achieve maximum aspiration and thermal efficiency.
Place the tip with the
component terminal in
the hole.
After pressing the desoldering key there is a slight delay until the self-contained vacuum pump
stops. This makes sure that the vacuum circuit is completely empty. If any solder remains are left
on a terminal after desoldering it, resolder it with fresh solder and repeat the desoldering operation.
When the solder liquefies,
gently rotate the tip so
that the compo nent
terminal can be lifted off.
Press the vacuum pump
button long enough to
remove the solder.
3. Aspirating1. Placing 2. Rotating
www.jbctools.com
3
A ø
B ø
C560-001
C560-002
C560-003
C560-004
C560-009
C560-014
Changing Tips
This operation should be done while the tip is hot and at a minimum temperature of 250°C, so that
any tin left inside is still molten.
1. Removing
Use the special spanner to unscrew the tip.
2. Inserting
Fit the new tip and tighten with the spanner
to make sure it is air tight.
Compatible Tips
The DR560 uses C560 tips.
Find the model that best suits your soldering needs in www.jbctools.com
Here are some C560 tips in real size:
250ºC minimum
C560-001 A=1,4 B=0,6 max. pin=0,4 mm
(A=0.05 B= 0.02 max. pin= 0.01 in)
C560-002 A=1,8 B=0,8 max. pin=0,6 mm
(A=0.07 B= 0.03 max. pin= 0.02 in)
C560-003 A=2,7 B=1 max. pin=0,8 mm
(A=0.1 B= 0.04 max. pin= 0.03 in)
C560-004 A=3,2 B=1,3 max. pin=1,1 mm
(A=0.12 B= 0.05 max. pin= 0.04 in)
C560-009 A=5 B=1,3 max. pin=1,1 mm
(A=0.19 B= 0.05 max. pin= 0.04 in)
C560-014 A=2,5 B=0,8 max. pin=0,6 mm
(A=0.09 B= 0.03 max. pin= 0.02 in)
4
1. Removing
Loosen the deposit lid (a),
remove the screw (b)
and withdraw the heating
element (c).
For this operation, turn off the station or disconnect the tool and wait until the tool temperature
drops to room temperature.
2. Placing
Insert the new Heating
Element (a), tighten the screw
(b) and then the lid (c).
Before placing, make sure
to insert the internal gasket
into the Glass Solder Collector.
b
a
c
b
c
a
!
!
Important
For a proper connection
it is essential to insert the
cartridge by lining it up to
the mark .
washer
Changing the heating element (Ref. DSV-DR)
Compatibility
The DSV-DR also works with
the previous version DR5600
Desoldering Iron (Ref. 5600010).
In this case, you must take out
the washer with a pliers.
www.jbctools.com
5