KE-1070_80_Operation_Manual2_Rev01_C2.pdf - 第7页

操作手册Ⅱ目录为了安全使用机器目录第 1 章设备概要 ··································································································· 1-1 1-1 前言 ··············································································…

为了安全使用 KE-1070/1070C/1080 的注意事项

1.为了防止触电引起的事故，请勿在接通电源的状态下打开电气设备箱。

2.为防止触电，请勿在拆下接地线的状态下运行。

1.为防止人身受伤，请勿在拆下安全罩、安全装置等状态下运行。

2.为防止人身受伤，请务必小心，以免头发、衣服等被卷入传送带链。此外，请勿戴手套。

3.为防止人身受伤，维护时（加油、调试、日常检修），请切断电源。

4.为防止人身受伤，请在电源线上使用漏电断路器。

注意

危险

1.本装置的操作系统采用 Windows XP（包括以太网通信功能）。

除安装本装置提供的软件之外，加装其他软件，不保证正常运行。对 SSD 内组装的文件

进行转移、重命名、文件夹·文件的压缩、复制，也同样不保证正常运行，敬请谅解。

● 万一出现此钟情况，需要更换新的 SSD，有可能丢失数据，务请格外注意。

注意

为保护操作系统，使用了 Enhanced Write Filter(EWF)组件，进行了 C 盘 ROM 化。

1.请不要在 C 盘保存文件。

把文件保存在 ROM 化后的 C 盘，会仿真占用主存储器。因而，把文件存在 C 盘里时，会

增加主存储器的使用量，压迫系统。反复保存后可能造成内存不足，显示系统错误，可

能需要重启本设备。

2.需要修改 OS 信息时，必须刷新 C 盘操作。操作方法请参见使用说明书「1－6 更新C盘的

操作」。

需要修改 OS 信息的操作是指下列事项：

·系统软件、Flex Line DB 的版本升级

·触摸屏自我校正

·添加打印机

·设置网络（IP 地址、工作组等）

·添加用户

·变更资源管理器的设置

·变更 UPS 实用程序（UPSilon2000）的设置

●要变更操作系统信息时，在修改 C 盘操作后，需要重启一次本装置。

注意

1.本装置配备有 UPS（可选项），以保护停电时的生产程序等。

为防止 UPS 内置电池劣化，请勿在非通电状态下将本装置放置 6 个月以上。

●本装置以电流总断路器及总开关 ON 的状态为通电状态。

注意

〈安全盖〉

1．开关安全盖时请注意下列事项。

• 打开安全盖时要把盖子向上开足直到上了锁，确认上了锁后再放开手。

没有上好锁就放开手时，盖子有落下来的危险。

• 关盖子时先解开锁，再关闭盖子。

（请注意，解开锁时不要使盖子落下来导致受伤。）

• 不要过渡增加盖子、手把等的负荷。

注意

1. 安装等时请不要站到机器上面，以免损坏外罩类。

1. 操作机器时，请注意以下事项。否则不能正确运行。

・不要使用任务管理器，强制结束操作。

・在机器工作中，请不要按下×按钮。

注意

操作手册Ⅱ目录

为了安全使用机器

第 1 章设备概要 ··································································································· 1-1

1-1 前言 ··························································································································· 1-1

1-2 特点 ··························································································································· 1-1

1-3 系统构成 ···················································································································· 1-4

1-3-1 KE-1070 系统构成····························································································· 1-4

1-3-2 KE-1070C 系统构成 ·························································································· 1-5

1-3-3 KE-1080 系统构成····························································································· 1-6

1-4 设备概要 ···················································································································· 1-7

1-4-1 本设备的构成···································································································· 1-7

1-4-1-1 贴片头单元的构成 ··················································································· 1-9

1-4-1-2 ATC 单元(Auto Tool Changer 自动工具交换)的构成 ····························· 1-10

1-4-1-3 吸嘴······································································································· 1-11

1-4-1-4 OCC 的构成··························································································· 1-12

1-4-1-5 VCS 的构造···························································································· 1-13

1-4-1-6 HMS······································································································· 1-14

1-4-2 机器规格········································································································· 1-15

1-4-3 对象元件及元件包装方式················································································ 1-17

1-4-4 印刷基板规格·································································································· 1-20

1-4-5 定心系统········································································································· 1-24

1-4-6 X,Y,Z,θ 轴的说明····························································································· 1-25

1-5 菜单的构成 ·············································································································· 1-26

1-6 通过模式 ·················································································································· 1-30

1-7 文件操作 ·················································································································· 1-31

1-7-1 新建················································································································ 1-31

1-7-2 打开（读入文件） ·························································································· 1-31

1-7-3 保存················································································································ 1-32

1-7-4 另存为 ············································································································ 1-32

1-7-5 文件管理········································································································· 1-32

1-7-6 生产程序初始位置 ·························································································· 1-33

1-7-7 设置打印机

····································································································· 1-33

1-7-

8 打印················································································································ 1-33

1-7-9 控制数据管理、设备信息的保存…、保存图像数据…····································· 1-33

1-7-10 硬件安全拆卸································································································ 1-33

1-7-11 C 盘的更新操作····························································································· 1-34

第 2 章制作生产程序 ···························································································· 2-1

2-1 流程图························································································································ 2-1

2-2 选项 ··························································································································· 2-2

2-2-1 用户组 ·············································································································· 2-2

2-2-1-1 变更用户组······························································································ 2-2

2-2-1-2 设置用户组环境······················································································· 2-3

2-2-2 设置用户组环境 ································································································ 2-3

2-3 制作生产程序············································································································· 2-4

2-3-1 启动生产程序编辑 ···························································································· 2-4

2-3-2 生产程序的制作步骤························································································· 2-4

2-3-3 基板数据··········································································································· 2-5

2-3-3-1 基本设置 ································································································· 2-5

2-3-3-2 尺寸设置 ································································································· 2-8

2-3-4 贴片数据········································································································· 2-25

操作手册Ⅱ目录

2-3-4-1 贴片数据画面的显示·············································································· 2-25

2-3-4-2 输入项目 ······························································································· 2-26

2-3-5 元件数据········································································································· 2-32

2-3-5-1 元件数据画面的显示·············································································· 2-32

2-3-5-2 元件数据的制作····················································································· 2-34

2-3-6 吸取数据········································································································· 2-61

2-3-6-1 吸取数据画面的显示·············································································· 2-61

2-3-6-2 设置项目 ······························································································· 2-64

2-3-7 图像数据········································································································· 2-67

2-3-7-1 图像数据画面显示 ················································································· 2-67

2-3-7-2 设置项目 ······························································································· 2-68

2-3-7-3 元件······································································································· 2-83

2-3-7-4 控制······································································································· 2-83

2-3-7-5 照明控制 ······························································································· 2-85

2-3-8 通用图像元件·································································································· 2-86

2-3-8-1 概要······································································································· 2-86

2-3-8-2 通用图像数据简易输入 ·········································································· 2-87

2-3-8-3 通用图像元件的规格·············································································· 2-94

2-3-8-4 通用图像元件的数据制作概要 ······························································· 2-95

2-3-8-5 通用图像的输入项目·············································································· 2-96

2-3-8-6 元件查看器·························································································· 2-103

2-3-9 数据完成状态································································································ 2-111

2-3-10 数据一致性检查 ·························································································· 2-112

2-4 优化 ······················································································································· 2-113

2-4-1 设置优化条件································································································ 2-113

2-4-1-1 元件供应数·························································································· 2-113

2-4-1-2 设置优化条件 ······················································································ 2-115

2-4-2 执行优化······································································································· 2-123

2-4-2-1 执行优化 ····························································································· 2-123

2-4-2-2 文件保存 ····························································································· 2-123

2-4-2-3 确认分开贴片数据 ··············································································· 2-124

2-4-2-4 吸嘴

分布 ·····························································································

2-125

2-4-2-5 供料器编排·························································································· 2-126

2-5 其他功能 ················································································································ 2-128

2-5-1 编辑·············································································································· 2-128

2-5-1-1 编辑菜单 ····························································································· 2-128

2-5-2 示教·············································································································· 2-135

2-5-2-1 HOD（手动操作设备）的使用方法 ······················································ 2-135

2-5-2-2 坐标的示教·························································································· 2-136

2-5-2-3 标记的示教·························································································· 2-138

2-5-3 设置环境······································································································· 2-146

2-5-4 机器操作······································································································· 2-148

2-5-4-1 传送····································································································· 2-149

2-5-4-2 测量····································································································· 2-151

2-5-4-3 检查····································································································· 2-155

2-5-4-4 确认····································································································· 2-158

2-5-4-5 管理····································································································· 2-164

2-5-4-6 元件示教 ····························································································· 2-165

2-5-5 打印·············································································································· 2-166

2-5-6 帮助·············································································································· 2-167

2-5-7 退出程序编辑································································································ 2-167