TS5624DMP-User-Guide.pdf - 第8页

8 8. MAINTENANCE OF AIR CYLINDER O-RING (Refer to figure 7 .0 and 8 .0 ) 1. Unscrew receiver screws (1 ). 2. Remove the DMP (2 ). 3. Remove the stroke control knob (3) and spring (4 ). 4. Remove the receiver assembly (5)…

100%1 / 12
7
7. DISPOSABLE MATERIAL PATH REMOVAL/REPLACEMENT:
Removal of a feed path assembly: Refer to figure 6.0
1. Release fluid pressure.
2. Remove syringe barrel or fluid line from the valve.
3. Loosen the lower receiver screws (4 - 5 turns) and pull out disposable material
path.
4. Dispose of the used feed path assembly in an appropriate waste container.
Installation of a new feed path assembly: Refer to figure 6.0
1. Insert a new feed path assembly into the valve housing. Ensure correct fitment
into the actuator.
2. Tighten lower receiver screws to torque setting specified below.
Torque Specifications
14 in lb. (1.58 N-m)
Figure 6.0
1. Loosen screws
4 - 5 turns.
2. Remove DMP
insert.
3. Insert new
DMP insert.
4. Tighten screws
evenly to torque
setting.
8
8. MAINTENANCE OF AIR CYLINDER O-RING (Refer to figure 7.0 and 8.0)
1. Unscrew receiver screws (1).
2. Remove the DMP (2).
3. Remove the stroke control knob (3) and spring (4).
4. Remove the receiver assembly (5).
5. Remover actuator (6).
6. Remove retaining ring (7), anti-rotate washer (8) and Mylar washer (9).
7. Remove piston (10) from air cylinder (11).
8. Replace O-ring (12) if damaged; otherwise lubricate O-ring with Bimba
HT-99, or equivalent.
9. Reinstall piston (10), retaining ring (7), anti-rotate washer (8) and Mylar
washer (9).
10. Reinstall actuator (6) as per position in Step 4. 90° offset to the air inlet.
11. Reinstall receiver assembly (5), leaving receiver screws loose.
12. Reinstall spring (4) and stroke control knob (3).
13. Install DMP (2) and set torque on receiver screws. - 14 in lb. (1.58 N-m)
Vertical slot must
face this way, 90°
offset to the air inlet.
Step 1
Figure 7.0
(12)
(10)
(1)
(2)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(10)
(11)
(9)
Step 2
Step 3
Step 6
Step 5
Step 4
9
9. SPARE PARTS
ITEM
PART NUMBER
DESCRIPTION
1
5620-000-004
End Cap
2
TSD1400-111APK
End Cap O-Ring (Pack of 10)
3
2800-0892
Washer, SS
4
3300-0578
Spring
5
TSD1120-11
Retaining Ring
6
TSD1109-43
Mylar Washer
7
5620-000-006
Anti-Rotate Washer
8
TSD1400-016APK
Piston O-Ring (Pack of 10)
9
5620-000-005
Piston
10
5620-000-003
Air Cylinder
11
A0100478
Air Hose/Connector Assembly, 4mm
12
TSD1003-20
Air Fitting, 4mm, Elbow
13
7509-0250
Actuator
14
7509-0270
Upper Receiver
15
2800-0463
Upper Receiver Screw
16
7509-0280
Lower Receiver
17
2800-0236
Washer
18
2800-0886
Screw
19
DMP-5624
Disposable Material Path (Pack of 10)
20
TSD1106-13
Mounting Screw
21
918-000-048
Mounting Bracket
22
7509-9100
Syringe Bracket W/Inserts (See Fig.5)
Lubrication: All O-Rings must be lubricated with Bimba HT-99, or equivalent.
Receiver Mounting Screws Torque (Item 18): 14 in lb. (1.58 N-m).
Figure 8.0