00198158-01_AI_Speed_Config_RV12_NC_EN.pdf - 第12页
Introduction Staff Qualifications and Training 1.3.4 Release History 12 Assembly Instructions E by SIPLACE 1.4 1 . 4 S t a f f Q u a lif ic a t io n s a n d T r a in in g Staff Qualifications and Training Qualified or ad…
Introduction
1.3.4 Release History Other Instructions
Assembly Instructions E by SIPLACE 11
1.3.3.3
1.3.3.3 Handling ESD Modules
Handling ESD Modules
Do not touch electronic modules unless it is absolutely essential to do so in order to carry out other work.
If it is necessary, make sure that you do not touch the pins or printed conductors when you pick up flat
modules.
Do not touch components unless
▪ You are constantly earthed by an ESD wrist strap or
▪ You are wearing ESD shoes or ESD shoe earthing strips on an ESD floor.
Always discharge yourself before you touch an electronic module. To do this, simply touch a conductive
and earthed object immediately before you touch the module (such as unpainted parts of a switch cab
-
inet, a water pipe, etc.).
Do not allow modules with chargeable and highly insulating materials to touch one another, e.g. plastic
films, insulating table surfaces or items of clothing made from synthetic fibers.
Always place the modules on a conductive surface (table with an ESD coating, conductive ESD foam,
ESD bag or container).
Do not bring modules near visual display units, monitors or televisions. Keep them at least 10 cm away
from the screen.
1.3.3.4
1.3.3.4 Measurements and Modifications to ESD Modules
Measurements and Modifications to ESD Modules
Measurements of the assemblies may only be taken if
▪ The measuring device has been grounded (e.g. via protective conductor) or
▪ The measuring head of the potential-free measuring device has been briefly discharged before
measurement (e.g. touching blank metal control unit housing).
► Always use an earthed soldering iron if you carry out any soldering work.
1.3.3.5
1.3.3.5 Dispatching ESD Modules
Dispatching ESD Modules
► Always store modules and components in conductive packaging (e.g. metallized plastic bags or met
-
al sleeves) and dispatch them in conductive packaging.
► If the packaging is not conductive, place the modules in a conductive envelope before packaging.
Use conductive foam rubber, ESD bags, domestic aluminum foil or paper, for example. NEVER use
plastic bags or film.
► If the module has integral batteries, ensure that the conductive packaging does not touch or short-
circuit the battery terminals and, if necessary, first cover the terminals with insulating tape or mate
-
rial.
1.3.4
1.3.4 Release History
Release History
Document
E by SIPLACE
Option Speed Config RV12 and Nozzle Changer
Assembly Instructions
Release Changes
01/2016 Initial release
Introduction
Staff Qualifications and Training 1.3.4 Release History
12 Assembly Instructions E by SIPLACE
1.4
1.4 Staff Qualifications and Training
Staff Qualifications and Training
Qualified or adequately trained personnel means that these people are familiar with the setting up, op
-
eration and maintenance of automatic placement systems and add-on devices and are suitably qualified,
e.g.:
▪ Have been trained, instructed or authorized to switch on and off, isolate, earth and identify electrical
circuits and system components in accordance with normal safety standards.
▪ Have been trained or instructed in the upkeep and use of appropriate safety equipment in accord
-
ance with normal safety standards.
▪ Have received first aid training.
Speed (Single-Sided) DLM-RV12 - Option 1
Assembly Instructions E by SIPLACE 13
2
2 Speed (Single-Sided) DLM-RV12 - Option 1
Speed (Single-Sided) DLM-RV12 - Option 1
A standard single sided machine includes an "NC Speed kit reject bin small" [03113189-xx].
"NC SPEED RV12 LOC 1 cpl." [03113197
-
xx] is located in the highlighted area.
▪ It consists of a "single row nozzle changer" [03106322-xx] base plate with four "active nozzle mag
-
azines" [03081446
-
xx] as shown above.
▪ For an upgrade in the field, the height measurement block SPEED [03119428 xx] must also be or
-
dered.
Nozzle maga zine type 30xx fo r RV12 [03081446-xx]
Height measurement block SPEED [03119428-xx]
Standard Speed (SS) RV12 Speed (SS) RV12 Option 1
1 Location 1 2 Location 2
Active nozzle magazine type (quick reference)
▪ Nozzle magazine type 30xx for RV12
[03081446
-
xx]
Height measurement block SPEED [03119428
-
xx]