YSM20_YSM20W_Mainte_E.pdf - 第107页
3-49 3 Periodic maintenance items n NOTE The tension measurement locations and tension standards of this machine's conveyor belt are as below. Adjust with tension meter as needed. Conveyor belt: T ension measurement…
3-48
3
Periodic maintenance items
5
Detach belt from conveyor.
Detach the conveyor belt from the pulley
and board guide.
6
Check the conveyor belt.
Check the transfer surface of the detached
belt for worn-out or scuffing. If the belt worn-
out amount or scuffing is large, replace the
conveyor belt while referring to "Chapter 6
How to replace consumable parts"
7
Clean the belt guides and pulleys.
1. Use a vacuum assembly (option) to suck
the belt wear debris on the belt guides
and sensors, etc.
2. Use a plastic spatula or similar tool to
remove the belt wear debris adhering to
the outer peripheral surface of pulleys.
3. Use a brush or similar tool to remove belt
wear debris caught in the belt guides.
c
CAUTION
Use a plastic spatula and brush to avoid scratching the
pulleys and guides.
c
CAUTION
Do not use a solvent (IPA, etc.) unless the guides and
pulleys are excessively dirty. If using a solvent, be
careful not to spill the solvent on the bearing in the
pulleys during cleaning.
8
Reattach the belt.
1. Reattach the belt temporarily while
putting it on the pulley.
2. Move the bracket (YSM20W Single-lane:
pulley) to the position marked in Step 4
and mount the bolts.
3.
If looseness of the belt is found, adjust the
bracket (pulley) position to apply tension.
n
NOTE
The following shows the conveyor belt tension standard
values of this machine. When necessary, adjust the
conveyor belt tension with a tension meter.
• YSM20 Dual-stage
Entrance, exit : 150 to 180Hz
W2-axis, W3-axis : 300 to 350Hz
• YSM20/YSM20W Dual-lane / YSM20 Single-lane
W1-axis : 420 to 460Hz
• YSM20W Single-lane (for transferring heavy boards)
W1-axis : 274 to 334Hz
c
CAUTION
The followings are tightening torques of the tensioner
mounting bolts. Do not tighten the bolt excessively.
Pulley bracket mounting bolt : 3.8 N•m.
Pulley mounting bolt : 5.5 N•m.
Cleaning the belt guide and pulley
Step 7
Spatula
(made of plastic)
Belt wear debris
sticking to pulley
Belt guide
Belt guide
Outer peripheral
surface of pulley
Brush
Outer peripheral surface of pulley
533D5-N2-10
3-49
3
Periodic maintenance items
n
NOTE
The tension measurement locations and tension standards of this machine's conveyor belt are as below.
Adjust with tension meter as needed.
Conveyor belt: Tension measurement locations and tension standards
YSM20
Transfer
direction
Dual-stage type
Tension measurement location:
STD: Tension of standard conveyor
EXT: Tension of extended conveyor
STD: 425 - 475 Hz
EXT: 100 - 120 Hz
Single-lane type
STD: 490 - 540 Hz
STD: 490 - 540 Hz
STD: 425 - 475 Hz
EXT: 100 - 120 Hz
STD: 420 - 460 Hz
EXT: 420 - 460 Hz
W1
W2W3
W4
Transfer
direction
53396-N2-00
3-50
3
Periodic maintenance items
Transfer direction
Dual-lane type
Lane 1
Lane 2
STD: 420- 460 Hz
EXT: 420 - 460 Hz
Single-lane type (transferring heavy boards)
STD: 420- 460 Hz
EXT: 420 - 460 Hz
STD: 274-334 Hz STD: 274-334 Hz
Transfer direction
Transfer direction
Conveyor belt: Tension measurement locations and tension standards
YSM20W
Tension measurement location:
STD: Tension of standard conveyor
EXT: Tension of extended conveyor
53397-N2-00