Service Manual SIPLACE SmartFeeder.pdf - 第238页

8 Repairs to SmartFeeder 2x8 mm X / Xi 8.16 Handle with control panel 238 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 8.16.3.1 Removing individual parts from the handle …

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.16 Handle with control panel

Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 237

8.16.3 Individual parts on the handle

Spare parts required

Fig.78: Individual parts on the handle SmartFeeder 2x8 mm X/Xi

NOTICE

Other slide for SmartFeeder 2x8 mmXi

In order to visually differentiate Xi feeder modules from the "normal" X feeder modules, a

different slide is used, with a clearly corrugated surface on the outside.

Feeder module Position Item no. Designation

SmartFeeder 2x8mmX 1 03092491-02 Slide assy. X24-104

SmartFeeder 2x8mmXi 1 03172631-01 Slide assy. X2x8i

SmartFeeder 2x8mmX

SmartFeeder 2x8 mm Xi

2 03009150Sxx Pressure spring VD-090V

3 03147373-01 Sleeve retaining spring X24-104Smart

curved

4 03033796-01 RF-SN75-2.5 x 6-9.8

5 03113312-01 Handle base X24-104

6 03167407-02 PCBA control panel X2x8 v4

7 03167618-01 Assembly spacer control panel X2x8 V4

8 03113588-01 Cover, handle X24-104

9 03110496-01 Window for control panel

10 03063592-01 Cable control panel X2x8

Tools required

●

Phillips screwdriver 0.9Nm

●

TORX screwdriver 0.6Nm, size T8

●

Tweezers or flat pliers

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.16 Handle with control panel

238 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

8.16.3.1 Removing individual parts from the handle

► Carefully place the feeder module with the right side down on a stable, level and clean sur-

face.

► Remove the left side cover (see 7.3.1 "Removing the Left Side Cover" [}102]).

► Remove the operating panel (see 7.15.2.1 "Removing the Control Panel and Board" [}152]).

If you have removed the operating panel, the cover on the foil stuffing unit will be accessible and

can be replaced if necessary.

► Pull the slide up and out of the handle. (1)

► Remove the pressure spring. (2)

► Remove the screw which fastens the spring

hook(1)

to the handle.

► Remove the spring hook.

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.16 Handle with control panel

Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 239

8.16.3.2 Fitting individual parts to the handle

► Hold the spring hook as shown(1) by the handle,

so that you can look through the opening and see

the hole for the screw.

► Screw the spring hook to the handle. Use a size

T8 TORX screwdriver with 0.6 Nm for this.

► Push one end of the pressure spring in the

handle, as shown.(1)

► Insert the slide into the other end of the pressure

spring.(2)

► Press the slide into the pressure spring and insert

it from above, into the handle.(3)

At this point, the cover on the foil stuffing unit will be accessible and can be replaced if necessary,

before you fit the operating panel.

► Fasten the operating panel (see 7.15.2.2 "Fitting the Control Panel and Board" [}153]).

► Fasten the left side cover (see 7.3.2 "Fitting the left side cover" [}102]).