Service Manual SIPLACE SmartFeeder.pdf - 第79页

6 Repairs to SmartFeeder 4 mm X / Xi 6.15 Handle with control panel Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 79 6.15.3.1 Removing individual parts from the handle ► C…

6 Repairs to SmartFeeder 4 mm X / Xi

6.15 Handle with control panel

78 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

6.15.3 Individual parts on the handle

Required spare parts

Fig.23: Individual parts on the handle SmartFeeder 4 mm X

NOTICE

Other slide for SmartFeeder 4mmXi

In order to visually differentiate Xi feeder modules from the "normal" X feeder modules, a

different slide is used, with a clearly corrugated surface on the outside.

Feeder module Position Item no. Designation

SmartFeeder 4mmX 1 03108403Sxx Slide for foil stuffing unit assy. X8Smart

SmartFeeder 4mmXi 1 03171389-xx Slide for foil stuffing unit assy. 4/8mm Xi

SmartFeeder 4mmX

SmartFeeder 4mmXi

2 03009150Sxx Pressure spring VD-090V

3 03095505-xx Retaining springs for foil stuffing unit

4 03033796-xx RF-SN75-2.5 x 6-9.8

5 03101437Sxx Window for control panel X8Smart

6 03101508Sxx Cover for foil stuffing unit X8Smart

Tools required

●

TORX screwdriver 0.6Nm, size T8

●

Tweezers or flat pliers

6 Repairs to SmartFeeder 4 mm X / Xi

6.15 Handle with control panel

Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 79

6.15.3.1 Removing individual parts from the handle

► Carefully place the feeder module with the right side down on a stable, level and clean sur-

face.

► Remove the left side cover (see 6.3.1 "Removing the Left Side Cover" [}30]).

► Remove the control panel (see 6.15.2.1 "Removing the Control Panel and Board" [}76]).

If you have removed the control panel, the cover on the foil stuffing unit will be accessible and can

be replaced if necessary.

► Pull the slide up and out of the handle. (1)

► Remove the pressure spring.(2)

► Remove the TORX screw which fastens the

spring hook(1)

to the handle.

► Remove the spring hook.

6 Repairs to SmartFeeder 4 mm X / Xi

6.15 Handle with control panel

80 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

6.15.3.2 Fitting individual parts to the handle

► Hold the spring hook as shown(1) by the handle,

so that you can look through the opening and see

the hole for the screw.

► Screw the spring hook to the handle. Use a size

T8 TORX screwdriver with 0.6 Nm for this.

► Push one end of the pressure spring in the

handle, as shown.(1)

► Insert the slide into the other end of the pressure

spring.(2)

► Press the slide into the pressure spring and insert

it from above, into the handle.(3)

At this point, the cover on the foil stuffing unit will be accessible and can be replaced if necessary,

before you fit the control panel.

► Fasten the control panel (see 6.15.2.2 "Fitting the Control Panel and Board" [}77]).

► Fasten the left side cover (see 6.3.2 "Fitting the Left Side Cover" [}30]).