Service Manual SIPLACE SmartFeeder.pdf - 第89页

6 Repairs to SmartFeeder 4 mm X / Xi 6.17 Foil container Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 89 ► Fasten the right side cover with the marked screws (see also th…

100%1 / 246
6 Repairs to SmartFeeder 4 mm X / Xi
6.17 Foil container
88 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
6.17.2 Foil box
Spare part required
Fig.27: Foil box
Feeder module Item no. Designation
SmartFeeder 4mmX
SmartFeeder 4mmXi
03125663-xx Foil box X4Smart V2
Tools required
●
Phillips screwdriver 0.9Nm
●
TORX screwdriver 0.6Nm, size T8
●
Flat-bladed screwdriver size 1
●
Tweezers
6.17.2.1 Removing the foil box
► Carefully place the feeder module with the left side down on a stable, level and clean surface.
► Remove the right side cover (see 6.3.3 "Removing the Right Side Cover" [}31]).
► Remove the 4 TORX screws marked in the dia-
gram. (1)
Use a T8 TORX screwdriver for this.
► Remove the Phillips screw marked in the dia-
gram. (2)
► Remove the cover flap with the shaft.(3)
► Carefully remove the insertion foil container.
6 Repairs to SmartFeeder 4 mm X / Xi
6.17 Foil container
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 89
► Fasten the right side cover with the marked
screws (see also the notes at 6.3.4
"Fitting the
Right Side Cover" [}32]).
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Remove the spring behind the rocker.
► Remove the left side cover assembly (see 6.3.1
"Removing the Left Side Cover" [}30]).
► Remove the rear sliding guide (see 8.2.1 "Re-
moving the Rear Sliding Guide" [}173]).
► Loosen the screw marked B with a Phillips
screwdriver.
► Loosen the 3 screws marked A with a TORX
screwdriver.
ð The lower stiffener (1) also loosened will be
pulled off the foil box at a later time.
► Remove the TORX screw fastening the filler
piece for the splice sensor.
6 Repairs to SmartFeeder 4 mm X / Xi
6.17 Foil container
90 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
► Remove the two TORX screws fastening the foil
box to the empty tape duct.
► Remove the two TORX screw fastening the foil
box (1)
to the foil stripping unit (2).
► Open the connection X202 on the control board.
► Remove the flat ribbon cable leading to the con-
trol panel.
► Reach between the foil box and the righthand
side cover with the finger of your right hand.(1)
► Use your left hand to carefully lift the top stiffener
together with the foil stripping unit.(2a)
► At the same time, press the foil box down with
the thumb of your right hand.(2b)
The connection between the foil stripping unit and the
foil box should now open.(3)
If the connection does not open:
► Move the rocker, to separate the tamp wheels of
the foil rocker from the rocker.