TK33045_PickHeightTeaching.pdf - 第3页

 2nd SMT Engineering Division Softw are Gro up IM Operations Y AMAHA MOTOR CO., L TD  MD OC-SOFT50389   3/24  1. M achine T ype and Soft w are V ersion This function is supported for the following machine type and …

100%1 / 24
2nd SMT Engineering Division Software Group
IM Operations
YAMAHA MOTOR CO., LTD
MDOC-SOFT50389
2/24
Contents
1. Machine Type and Software Version .................................................................................. 3
2. Overview ............................................................................................................................. 3
2.1 Target ............................................................................................................................ 4
3. Function Details .................................................................................................................. 5
3.1 Using Method ................................................................................................................ 6
3.2 Response to12mm or larger feeders
(▲2)
..................................................................... 7
3.3 Response to Trays
(▲3)
................................................................................................. 8
3.4 Pick Height Take Over Function ................................................................................... 9
3.5 Error Message............................................................................................................. 10
4. Setting Method .................................................................................................................. 14
4.1 Machine Setting .......................................................................................................... 14
4.2 Takeover of Parts Data................................................................................................ 19
4.3 Reading fixed board data ............................................................................................ 20
5. Limitations ......................................................................................................................... 21
6. Suggestions at upgrading software .................................................................................. 22
6.1. Mark data setting for guide recognition ..................................................................... 22
2nd SMT Engineering Division Software Group
IM Operations
YAMAHA MOTOR CO., LTD
MDOC-SOFT50389
3/24
1. Machine Type and Software Version
This function is supported for the following machine type and software version.
Table 1.1 Machine Type and Software Version (8mm or smaller)
Machine・Software
Version Note
YSM40, YSM20 V4.48STD R1.000 or later
YS100, YS12 series
YS24(X) series
V3.45STD R1.000 or later
In the following version, 12mm or larger feeders are supported with this function.
(▲2)
Table 1.2 Machine Type and Software Version (12mm or larger)
Machine･Software
Version Note
YSM40, YSM20 V4.52STD R1.000 or later
YS100, YS12 series
YS24(X) series
V3.47STD R1.000 or later
In the following versions, Tray feeder is supported with this function.
(▲3)
Table 1.3 Machine Type and Software Version (Tray feeder)
Machine/Software Version Note
YSM40, YSM20 V4.52STD R1.000 or later
YS100, YS12 series
YS24(X) series
V3.47STD R1.000 or later
2. Overview
This function measures pick height properly by checking vacuum level at moving the head to
the tape guide of a feeder. This function measures pick height properly by checking vacuum
level at moving a head close to the target pick height.
To determine pick height, it used to be necessary to measure the tape thickness by caliper,
and to adjust the height considering pick up rate. With this function, pick height is
automatically measured properly, so that you don’t need to create height data before the first
use of the machine.
2nd SMT Engineering Division Software Group
IM Operations
YAMAHA MOTOR CO., LTD
MDOC-SOFT50389
4/24
2.1 Target
1. All feeders, Auto Tray Stacker and Manual Tray Stacker are supported. Stick, bulk
feeders are excluded.
2. On an 8mm or smaller feeder (hereafter “8mm feeder), supported feeder guide types
are iron and carbon.
Therefore, when one machine has both of above types of tape guides, guide
recognition is necessary to distinguish iron and carbon.
3. Supported nozzle types are as follows.
Table 2.1 Nozzle Type of 8mm feeders or smaller
30X 31X 50X 51X 60X Note
301 311 501 511 601
302 312 502 512 602
313 513
303 314 503 514 603 Carbon tape guide cannot be measured.
309
3010
310
3110
510 On a YS series mounter, 310 nozzle needs
to be set as a special nozzle.
3010 and 3110 nozzles are available only
on YSM20.
Table 2.2 Nozzle Type of 12mm feeders or larger.
(▲2)
30X 31X 50X 51X 60X Note
All nozzle types There is a possibility that it doesn’t work
depending on the open vacuum level.
Table 2.3 Nozzle Type of Tray feeder.
(▲3)
30X 31X 50X 51X 60X Note
All nozzle types There is a possibility that it doesn’t work
depending on the open vacuum level.