CP-7[732-742]-series Mechanical Reference(2.9E).pdf - 第118页

Lubrication Checklist T010Ec 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Daphne Exponex No. 2 Multemp LRL3 Daphne Super Multi Oil 32 Daphne Exponex No. 2 Multemp LRL3 Daphne Super Multi Oil 32…

2.17 Lubricating the Cam Lever Air Cylinder

Procedure

1. Open the lid of the lubricator with a Phillips driver.

2. Lower the lubricator cover.

3. Visually check the oil level of the oil tank and slowly pour in the oil to the

lubricator. Be sure not to exceed the upper limit while pouring in the oil.

Note The maximum amount of oil that can be supplied to the lubricator is 75 cc. If the oil

level does not reach the tip of the pipe inside the case, there will be insufficient oil to

lubricate the cylinder.

4. Replace the lubricator cover and attach the oil inlet cap.

5. Check and discard of any accumulated waste oil in the collection bottle.

Cam lever air cylinder

(52)

Upper limit

Case

Pipe

Cover

Bottle

Lubricator

Lid

Lower limit

C7SM3084a

Turbine oil + NASKALUBE (*) Every 6 months

T017Eb

Lubrication points

Schedule

Types of lubricant

Air cylinder

(*) The lubrication used is a Fuji special blend (Turbine oil + NASKALUBE).

Contact Fuji when placing an order.

Part 3 Chapter 2 Lubrication

Edition 2.9 3-2-26 CP-7 series Mechanical Reference

Lubrication Checklist

T010Ec

Daphne Exponex No. 2

Multemp LRL3

Daphne Super Multi Oil 32

Daphne Exponex No. 2

Multemp LRL3

Daphne Super Multi Oil 32

Multemp SRL

Daphne Exponex No. 2

AFC grease

Daphne Exponex No. 2

AFC grease

Daphne Exponex No. 2

AFC grease

Daphne Exponex No. 2

AFC grease

Daphne Exponex No. 2

AFC grease

Every 3 months

Monthly

Every 3 months

Monthly

Every 3 months

Monthly

Every 6 months

Every 3 months

Monthly

Every 3 months

Monthly

Weekly

Monthly

Lubrication points

Schedule

CheckTypes of lubricant

XY-table

Conveyors

Carriers

Tape advance

link

Cam box

Tape cutter

X-axis LM block

X-axis ball screw

X-axis screw cover

Y-axis LM block

Y-axis ball screw

Y-axis screw cover

Z-axis ball screw

Ball screw

Shaft

Lifter guide bar

LM block (742ME, 742E)

LM rail

Cam follower

Tape feed lever

Shaft

Joint

Cam

Cam lever pivot (7 points)

Cam lever bearing

NZ-axis ball screw

NZ-axis LM rail

NZ-axis holder

NZ-axis LM block

-axis connecting pin

Movable cutter

Cam follower

Thrust bearing

Part 3 Chapter 2 Lubrication

Edition 2.9 3-2-27 CP-7 series Mechanical Reference

T020

ST3 Nozzle Clutch

Every 3 months

Monthly

Every 3 months

Monthly

Every 3 months

Monthly

Every 3 months

Monthly

Every 3 months

Monthly

Every 3 months

Every 3 yrs or

12,000 hrs

Every 6 months

*: Fuji special blend

Lubrication points

Schedule

CheckTypes of lubricant

AFC grease

Daphne Exponex No. 2

Multemp LRL3

Daphne Exponex No. 2

AFC grease

Daphne Exponex No. 2

AFC grease

Daphne Exponex No. 2

AFC grease

Daphne Exponex No. 2

SHC 630

Turbine oil + NASKALUBE*

Rod ends

D-axis carriers

Rotary head

ST9 Air valve push pin

Parts reject unit

Pallet table

Rear cover

Nozzle changer

LM Block

Rod end

D-axis LM block

D-axis ball screw

Cam follower

Turret groove

Helical gear

LM rail

Spline shaft

Wave washer

Valve push pin

Cam follower

LM rail

Pallet clamp surface

Clamp pin

Spline shaft

Beveled gear

Moveable sections on

the lever

Clutch engagement

surface

Thrust bearing

Slide rail

Oil cooler

Air cylinder

Index unit

Cam lever

Part 3 Chapter 2 Lubrication

Edition 2.9 3-2-28 CP-7 series Mechanical Reference