SECS GEM Manual.pdf - 第145页
GEM Manual for DEK Printers Event M essages Issue 1.6 January 22, 2018 Page 145 of 171 40050 Boar d fiducial 3 not found. 40051 Screen f iducial 1 not found. 40052 Screen f iducial 2 not found. 40053 Screen f iducial 3 n…
GEM Manual for DEK Printers Event Messages
Issue 1.6 January 22, 2018 Page 144 of 171
31220 Print pressure error.
31221 File error.
31222 Unable to recover.
31223 Recovery started.
31224 Recovered.
31225 Upline transfer error.
31226 Downline transfer error.
31227 Dual shuttle fault.
31230 Screen changer fault.
31232 Lid bolt fault.
31233 Alignment out of range.
31417 Comms error.
31303 Barcode read failure.
31304 Barcode mismatch.
31305 Screen couplings failed.
31306 Motion control timeout.
31307 Camera X failed to position.
31308 Camera Y failed to position.
31309 Stencil aperture blocked.
31310 Stencil smeared.
31311 Paste on pad inspection error.
31312 Bridging detected by inspection system.
31313 Alignment error detected by inspection system.
31321 Event log disk file full.
31322 Proflow error.
31340 CAN node down.
31341 CAN node recovered.
31342 CAN bus down.
31343 CAN bus comms restored.
31344 Invalid CAN response.
31433 CAN bus recovered.
31460 Volume alarm.
40006 Dongle error.
40028 Roll Height Monitor failed.
40043 Knead pressure error (front).
40044 Knead pressure error (rear).
40045 Print pressure error (front).
40046 Print pressure error (rear).
40047 Servo following error.
40048 Board fiducial 1 not found.
40049 Board fiducial 2 not found.
GEM Manual for DEK Printers Event Messages
Issue 1.6 January 22, 2018 Page 145 of 171
40050 Board fiducial 3 not found.
40051 Screen fiducial 1 not found.
40052 Screen fiducial 2 not found.
40053 Screen fiducial 3 not found.
40054 Select mark not found.
40056 Bad tooling vacuum.
40146 Cleaner detached from camera.
40147 Recovered cleaner detached from camera.
40148 Method of post print analysis is not enabled.
40149 Producing without post print analysis.
40150 Ball escape detected.
40152 Verification item failed (see DVID 2034).
40157 Product ID verification failed.
40300 Advanced Adjust Entered.
40320 Cleaner Vacuum Sense Error.
GEM Manual for DEK Printers Event Messages
Issue 1.6 January 22, 2018 Page 146 of 171
8.9 Equipment Specific Information Events
EVENT - CEID
DESCRIPTION
10002 System power on.
31251 Line power on.
31255 Printer ready.
31256 Head raised.
31257 Head closed.
31260 Cycle aborted.
31261 Cycle completed.
31262 Cleaning screen.
31263 Parameter adjusted. (See Appendix A)
31264 Setup started.
31272 Setup ended.
31273 Start print cycle.
31275 End print cycle.
31277 Board printed.
31278 Operator log on.
31279 Operator log off.
31280 Clear batch count.
31281 Start maintenance.
31282 End maintenance.
31283 Pressure recalibrated.
31284 Offset recalibrated.
31285 X,Y scale recalibrated.
31286 Theta recalibrated.
31287 Configuration change.
31288 Start diagnostics.
31289 End diagnostics.
31290 Flood height reset.
31291 Camera reference reset.
31292 Thickness recalibrated.
31293 Vision height reset.
31294 Print height reset.
31296 Software updated.
31297 New event log.
31298 Front reference position reset.
31299 Front reference height reset.
31300 Rear reference height reset.
31301 No cleaner paper.
31302 No cleaner solvent.