Operating Instructions_VF366_en.pdf - 第28页
2|Technical data 2.2.2 Bottom pre-heating, dynamic radiator cassette Description Type of heating Dynamic emitter cartridge Rated power (kW) at 400V 22 ( = 10 x 2.2) Dimensions of the emitter cartridge L x W (mm) 700 x …
2|Technical data
Description
Air humidity (%, non-condensing) 20…95
Continuous noise level (dB A) < 60
2.1.6 Safety devices
Designation
Main switch Lockable
Emergency STOP pushbutton (pieces) 3
Exhaust air duct monitoring With differential pressure switch
Hood Release via hardware / software safety
switch
2.1.7 Electrical data of the entire system
2.1.7.1 Connection data*
Description
Mains voltage 5-wire system N/PE (V) 3 x 230 V / 400 V
Voltage tolerance (%) ± 10
Mains frequency (Hz) 50 / 60
Pre-fuse (A, delayed action)* 3 x 125
Power consumption (kW)* 30
Nominal current consumption (A)* 50
*Depending on the respective development stage. The actual values are specified
on the type plate of your soldering system.
2.2 Technical data of the single units
2.2.1 Spray fluxer
Designation
Flux material stock 2
Flux material type according to IEC
61190-1-1*
RO, RE, OR
Flux material effectiveness level L0, L1, M0
Spray nozzle (µm), alternative sizes avail-
able on request
130
Spray pressure (bar) 0.5…1
Spray application width with 130 µm
spray nozzle (mm)
2…8
Flux material speed (mm/sec) 20
Positioning speed (mm/sec) 400
Positioning accuracy (mm) ± 0.2
*The materials used in the fluxer unit are approved for the above-mentioned flux.
Ersa GmbH Operating Instructions_VF366_en|Rev. 14|30/11/2017 27/551
2|Technical data
2.2.2 Bottom pre-heating, dynamic radiator cassette
Description
Type of heating Dynamic emitter cartridge
Rated power (kW) at 400V 22 ( = 10 x 2.2)
Dimensions of the emitter cartridge L x
W (mm)
700 x 850
* Depending on the development stage, several preheating radiators can be in-
stalled.
2.2.3 Top pre-heating, compressed air heater (option)
Description
Type of heating Medium wave emitters, convection
Rated power (kW) at 230V 8 ( = 2 x 4.0)
Dimensions of the emitter cartridge L x
W (mm)
600 x 865
Pneumatics stand-by pressure (MPa) 0.03
Pneumatics working pressure (MPa) 0.3
Ersa GmbH Operating Instructions_VF366_en|Rev. 14|30/11/2017 28/551
2|Technical data
2.2.4 Point and path soldering module
Description
Module type Point and path soldering module
Heating output (kW) 1.15
Solder content approx. (Kg) 13
Heat-up time to 280°C (h) 1.25
Maximum solder temperature (°C) 330
Minimum inside diameter of the solder
nozzle (mm)
3
Smallest outer diameter of the solder
nozzle (mm)
6
Maximum solder wave height (mm) 5
Minimum side clearance (mm) 3
Soldering speed X/Y axis (mm/sec) 10
X/Y axis positioning speed (mm/sec) 0.5…200
Positioning speed Z axis (mm/sec) 0.5…100
Positioning accuracy (mm) ± 0.15
Handling system 3-axis system with servo drives
Depending on the development stage, several soldering modules can be installed.
2.2.5 Solder feeding: Point and path soldering module
Description
Type of solder lead Solder wire
Maximum wire diameter (mm) 2
Maximum coil diameter (mm) 125
Maximum coil height (mm) 125
Maximum roller weight (Kg) 4
2.2.6 Single-track conveyor system
Description
Type Frameless conveyor system
Conveyor system Segmented single feeds
Conveyor speed (m/min) 0,2…10
Standard conveyor width (mm) 60…610
Type of conveyor width adjustment Motor driven, fixed rail in front
Conveyor angle (°), not adjustable 0
Board length (mm) 120…610
Board width (mm) 63,5…610
Max. board weight (kg) 8
Board overlay (mm)
1
3
Maximum height of components on the
PCB (mm)
120
Maximum height of components on the
PCB (mm)
2
30
Ersa GmbH Operating Instructions_VF366_en|Rev. 14|30/11/2017 29/551