00198788-01_UM_SSI_DE_EN.pdf - 第37页

1 Introduction 1.2 Important Notes about this Manual User Manual / Bedienungsanleitung SIPLACE Single Slot Interface 05/2021 37 1.1.6 Environmentally-friendly disposal of materials and components Our products are manufac…

1 Introduction

1.1 Module Description

36 User Manual / Bedienungsanleitung SIPLACE Single Slot Interface 05/2021

Ambient conditions for module operation

Temperature range 15°C to 35°C

Atmospheric humidity 30% to 75%

Ambient pressure > 750mbar

1.1.3 EU Declaration of Conformity

The product described below conforms to the regulations and standards listed in the EU Decla-

ration of Conformity provided.

Type Single Slot Interface

Item no.: 00120676-xx

Manufacturer:

ASM Assembly Systems GmbH & Co.KG

Rupert-Mayer-Str. 44

81379 Munich

Germany

1.1.4 Correct Usage

The product may only be used for its intended purposes as described in the catalogs and technical

descriptions, meaning for operation and troubleshooting of X feeder modules outside the place-

ment machine or a pre-setup area and only with the third-party equipment and components recom-

mended or permitted by ASM Assembly Systems GmbH & Co. KG.

Any other use is deemed to be incorrect and not as prescribed.

In the case of incorrect usage, ASMAssembly SystemsGmbH&Co.KG will not assume liability

for any damage which occurs and will not guarantee the correct and proper function of machine

components.

Prescribed or correct usage includes the observance of all the instructions in this user guide.

The proper and safe operation of the product requires correct transportation, storage, installation

and assembly, plus careful, accurate utilization and servicing.

1.1.5 Incorrect Usage

Failure to use the product as prescribed can result in both danger to life and limb and material

damage. For this reason, non-prescribed usage is prohibited. If the product is not used as pre-

scribed, ASM Assembly Systems GmbH & Co. KG will not accept liability for any damage that may

occur and will not guarantee that the components will work properly and without problems.

Non-prescribed use of the module includes the following examples:

●

The use of feeder modules that do not meet the permitted specification.

●

Use of unauthorized accessories and additional modules.

●

Use of the module by unqualified personnel.

1 Introduction

1.2 Important Notes about this Manual

User Manual / Bedienungsanleitung SIPLACE Single Slot Interface 05/2021 37

1.1.6 Environmentally-friendly disposal of materials and components

Our products are manufactured using only materials and parts that can be easily separated and

disposed of in an environmentally-friendly way.

NOTICE

Observe the applicable regulations

The company operating the system has sole responsibility for the proper, environmentally-

friendly disposal of machines, working materials, consumable materials and wear parts.

► Please observe your national statutory provisions for waste disposal and environ-

mental protection.

1.1.7 Electromagnetic compatibility (EMC)

All SIPLACE products are designed and tested for professional use in industrial applications. Elec-

tromagnetic compatibility in terms of the emission of interference cannot be guaranteed in any

other environment.

1.1.8 Use of original accessories and spare parts

Only use original spare parts and authorized accessories. The use of other parts will affect safety

and will invalidate the liability for any consequential damage.

1.2 Important Notes about this Manual

1.2.1 Contents and Filing of this Manual

This User Manual contains basic information that must be observed when setting up, operating and

maintaining the module. The service engineers, qualified staff, operators and users must therefore

read it before commencing installation and commissioning. The instructions must be kept perman-

ently accessible wherever the module is used.

In addition, the user must ensure that the employees have fully understood the contents of the user

manual.

1.2.2 Danger notes

WARNING

Danger notes

► Work may only be performed on the SIPLACE Single Slot Interface if the personnel

concerned have a thorough knowledge of the relevant section of the user guide.

► All work must be carried out by appropriately trained and qualified personnel.

► All warnings, cautions and hazard notes must be observed.

► Carefully read through the chapter on operational safety for this purpose.

1.2.3 Manufacturer's/supplier's liability

We draw your attention to the fact that these instructions only contain descriptive and explanatory

material and do not include any contractual conditions or undertakings. All obligations of ASM

Assembly Systems GmbH & Co. KG are conclusively specified in the respective contract, on the

basis of which you have received the machine described therein. This applies in particular to all

statements regarding performance or service life and the agreed liability for faults or defects. The

provisions of the contract regarding the liability for faults or defect are neither extended nor restric-

ted by any statements in this manual.

1 Introduction

1.2 Important Notes about this Manual

38 User Manual / Bedienungsanleitung SIPLACE Single Slot Interface 05/2021

1.2.4 Release History

Document

SIPLACE Single Slot Interface

Instruction manual

Release Amendments

05/2021 First edition

1.2.5 Further Information

1.2.5.1 How To Get Information

If you have any questions about this manual or if you would like more information about certain

subjects, please contact your local SIPLACE branch or us directly:

ASM Assembly Systems GmbH & Co. KG

Rupert-Mayer-Str. 44

81379 München

1.2.5.2 SIPLACE on the World Wide Web (WWW)

You can choose between the German and English version.

The different sections contain information about our products, services and contact persons.

In addition, registered customers can also access the MySIPLACE user group. Here, you can

access special information about our placement systems, e.g.:

●

Technical documentation

●

Technical information

●

Spare parts lists

Registration for the MySIPLACE user group is very simple:

► Click on MyASM and then on Registrieren.

► Fill in the registration form and send it off to us.

Soon afterwards, you will receive your access authorization with user name and password.