YS100_Ope_E.pdf - 第28页
9 9.1 Side-view camera 1-2 9 9.2 0 9.3 Coplanarity checker 1-3 1 Chapter 2 Basic operation 1 1.1 Canceling emergency stop 2- 1 1.2 Clearing an err…
General Contents
About this manual
1. Using this manual i
1.1 Available manuals i
i
2. Contents of each chapter iii
3. Page layout iv
Chapter 1 Part names and functions
1
3
2.1 Keyboard and mouse 1-3
4
3. Head assembly 1-5
3.1 Component pick-and-place head 1-5
3.1.1 Eight-in-line multi-head (FNC) assembly 1-5
3.1.2 Eight-in-line multi-head (SF) assembly 1-6
3.2 Nozzle types 1-7
3.2.1
Nozzles for the eight-in-line head assembly 1-7
9
4. Component supply section 1-11
4.1 Supplying components from feeder plates 1-11
4.1.1 Fixed feeder plates 1-11
4.1.2 Feeder exchange carriage 1-14
4.2 Supplying components from trays 1-15
4.2.1 dYTF main unit 1-15
4.2.2 sATS main unit 1-17
5.
Conveyor unit and component recognition system
1-19
6. Axis configuration 1-20
1
7.1 Performing a nozzle shaft blow 1-22
7
8.1 Tape cutting during component mounting 1-27
8.2 Tape cutting during board conveying 1-28
8
EPL1127130
9
9.1 Side-view camera 1-29
9.2 0
9.3 Coplanarity checker 1-31
Chapter 2 Basic operation
1
1.1 Canceling emergency stop 2-1
1.2 Clearing an error 2-2
1.3 Typical errors and troubleshooting 2-3
0
0
2.2 Setup screen 2-13
2.3 Unit screen 2-14
3. Starting and stopping the machine 2-19
3.1 Pre-operation check 2-20
3.2 Starting the machine 2-21
3.3 Warming up the machine 2-23
5
3.4.1 Conveyor unit setup flow 2-25
3.4.2 Conveyor width 2-26
3.4.3 Board hold plates 2-27
3.4.4 Push-up pins 2-28
4. Preparing the component supply unit 2-29
4.1 Tape feeder 2-29
4.1.1 Setting the tape 2-29
4.1.2 Setting a tape feed pitch 2-34
4.1.3 Installation on a mounter 2-38
4.2 Wide multi-stick feeder 2-39
4.2.1 Installation of tracks and sticks 2-39
4.2.2 Installation on a mounter 2-42
4.3 Tray changer 2-43
4.3.1 Setting the component trays in the pallet 2-44
4.3.2 Setting the pallet in the magazine 2-45
4.3.3 Replacing a magazine or pallets during operation (dYTF) 2-47
5. Settings on the mounter side 2-50
5.1 Setting the "Package" parameter. 2-50
5
Chapter 3 Starting and ending production
1. Starting production 3-1
1.1 Resuming operation from the stopped point 3-6
1.1.1 Loading the saved data 3-7
1.1.2 Editing mount flags 3-7
1.2 Using the "block skip function" 3-8
1.2.1 Selecting the blocks 3-9
1.2.2 Starting operation 3-10
2. Ending production and turning power off 3-11
3
3.1 Production 3-13
5
7
9
3.5 Alignment 3-21
3.6 Retry 3-22
3
4
5
3.10 Pick Rate Warning 3-27
3.11 Coplanarity checker 3-30
Appendix
A1. Specifications A-1
Index