Anritsu_MG3692C.PDF - 第13页

13 Inputs and Outputs* *Connectors may be available but not active, if option is not ordered. ** Options (7 & 18), (7 & 20), (8 & 9) are mutually exclusive, as they share the same rear panel space. MG3690C Re…

Millimeter Wave Multipliers

- 63850 series

(Option 18 recommended for DC bias.)

63850 series external, waveguide output, multipliers are available for banded frequency

coverage up to 325 GHz.

These external multipliers require at a minimum an MG3692C, with 20 GHz coverage.

The output power required to drive the modules is +10 dBm. They can be powered up

by an external power supply (+12 Vdc, 1.5A typ.) using the supplied double banana

power cord. It is recommended to purchase an MG3690C with option 18, which adds the

capability to bias these modules without the need of an additional power supply. Option 18

adds a rear panel Twinax connector that supplies the proper DC bias for these modules, and

a cable to power them up. Option 18 is not available with options 7 and 15.

63850 series multipliers have a saturated, unleveled, output power, yet their inherent

flatness is exceptional. Modulating the input drive will indeed modulate the output, except

for the case of Amplitude Modulation. Since the output is saturated, Amplitude Modulation

is not recommended with these mmW modules. Frequency and Phase Modulation is

possible, but the achieved deviation will be multiplied based on the multiplication factor of

the module. Pulse modulation is also possible, with even sharper rise and fall times than

the input. All modulation performances are not specified.

For ease of operation, the MG3690C allows the user to enter a frequency scaling factor,

the module's multiplication factor, which will be used only for purposes of displaying the

proper frequency at the output of the mmW module, on the MG3690C front panel display.

MG3690C with 63850 Series Millimeter Wave Multiplier

mmW Frequency Coverage

These mmW modules are produced by OML Inc. (Oleson Microwave Labs), located in Morgan Hill, CA., with mutual collaborative experiences over many years.

For detailed and up-to-date specifications, please call OML, Inc. or visit their website at www.oml-mmw.com.

Waveguide output flanges are per MIL.F-3922/67B-(xxx)

Power rolls off from –15 dBm at 200 GHz, to –25 dBm typical at 220 GHz.

Output power is estimated.

Multiplier p/n

63850-15 63850-12 63850-10 63850-08 63850-06 63850-05 63850-03

Frequency 50 GHz - 75 GHz 60 GHz - 90 GHz 75 GHz - 110 GHz 90 GHz - 140 GHz 110 GHz - 170 GHz 140 GHz - 220 GHz 220 GHz - 325 GHz

Waveguide Output WR-15 WR-12 WR-10 WR-08 WR-06 WR-05 WR-03

Flange

(008) (009) (010) (M08) (M06) (M05) (M03)

Output Power

(typical)

+8 dBm +6 dBm +5 dBm –5 dBm –13 dBm

–15 dBm

–25 dBm

Output Flatness

(typical) (Unleveled)

± 2 dB ± 2 dB ± 3 dB –– –– –– ––

Output Match > 12 dB > 12 dB > 12 dB > 12 dB > 12 dB > 12 dB 6 dB (typical)

Multiplication

Factor (m)

x4 x6 x6 x8 x12 x12 x18

Input Frequency 12.5 GHz - 18.75 GHz 10.0 GHz - 15.0 GHz 12.5 GHz - 18.4 GHz 11.2 GHz - 17.5 GHz 9.1 GHz - 14.2 GHz 11.6 GHz - 18.4 GHz 12.2 GHz - 18.1 GHz

Frequency Accuracy (LO Synthesizer's Accuracy x m)

Frequency Resolution (LO Synthesizer's Resolution x m)

Harmonics & Spurious –15 dBc (typical)

Input Power Required +10 dBm

RF Input Connector SMA (female)

DC Power 12 Vdc, 1.5A (double banana power cord included) Option 18 is recommended on the synthesizer, to supply the necessary bias.

Dimensions 120 mm x 110 mm x 70 mm (not including feet or interfaces)

Weight < 1 kg

Temperature +20 ºC to +30 ºC

Inputs and Outputs*

*Connectors may be available but not active, if option is not ordered.

** Options (7 & 18), (7 & 20), (8 & 9) are mutually exclusive, as they share the same

rear panel space.

MG3690C Rear Panel

EXT ALC IN Provides for leveling the RF output signal externally with

either a detector or power meter. Signal requirements are

shown in the RF Output specifications. BNC type, rear panel.

RF OUTPUT** Provides for RF output from 50 Ω source impedance.

(Option 9) Option 9 moves the RF Output connector from the front to the

rear panel. K Connector (female) fmax ≤ 40 GHz V Connector

(female) fmax ≥ 40 GHz.

10 MHz REF IN Accepts an external 10 MHz ± 50 Hz, 0 dBm to +20 dBm

time-base signal. Automatically disconnects the internal

high-stability time-base option, if installed. 50 Ω impedance.

BNC type, rear panel.

10 MHz REF OUT Provides a 1 Vp-p, AC coupled, 10 MHz signal derived from

the internal frequency standard. 50 Ω impedance. BNC

type, rear panel.

HORIZ OUT Provides 0V at beginning and +10V at end of sweep,

(Horizontal Sweep Output) regardless of sweep width. In CW mode, the voltage is

proportional to frequency between 0V at low end and +10V at

the high end of range. In CW mode, if CW RAMP is enabled, a

repetitive, 0V to +10V ramp is provided. BNC type, rear panel.

EFC IN Provides the capability to frequency modulate the internal

crystal oscillator, allowing phase locking the synthesizer

inside an external lock loop. Specifications on page 2. BNC

type, rear panel.

AUX I/O Provides for most of the rear panel BNC connections

(Auxiliary Input/Output) through a single, 25-pin, D type connector. Supports

master-slave operation with another synthesizer or allows

for a single-cable interface with the Model 56100A Scalar

Network Analyzer and other Anritsu instruments (see figure

below). 25 pin D-type, rear panel.

SERIAL I/O Provides access to RS-232 terminal ports to support

service and calibration functions and master-slave

operations. RJ45 type, rear panel.

IEEE-488 GPIB Provides input/output connections for the General Purpose

Interface Bus (GPIB). Type 57, rear panel.

mmW BIAS** Provides the bias for the external waveguide multipliers for

(Option 18) coverage up to 325 GHz. Twinax, rear panel.

RF, LO, IF** Provides access to an internal IF up-conversion mixer.

(Option 7) K Connector (female) 3X, rear panel.

PULSE TRIG IN Accepts an external TTL compatible signal to pulse

(Option 26) modulate the RF output signal or to trigger or to gate the

optional internal pulse generator. BNC type, rear panel.

PULSE SYNC OUT Provides a TTL compatible signal, synchronized to the

(Option 27) internal pulse modulation output. BNC type, rear panel.

PULSE VIDEO OUT Provides a video modulating signal from the internal pulse

(Option 27) generator. BNC type, rear panel.

AM IN Accepts an external signal to amplitude modulate the

(Option 14) RF output signal, 50 Ω impedance. BNC type, rear panel.

FM/ΦM IN Accepts an external signal to frequency or phase modulate

(Option 12) the RF output signal. 50 Ω impedance. BNC type, rear panel.

AM OUT Provides the amplitude modulation waveform from the

(Option 27) internal LF generator. BNC type, rear panel.

FM/ΦM OUT Provides the frequency or phase modulation waveform from

(Option 27) the internal LF generator. BNC type, rear panel.

SCAN MOD IN** Accepts an external signal to scan modulate the RF output

(Option 20) signal. High Impedance. BNC type, rear panel.

POWER MONITOR IN Accepts an external detector for power monitoring. Custom

(Option 8) type, rear panel.

Aux I/O pins:

1. Horizontal Output

2. Chassis Ground

3. Sequential Sync Output

4. Low Alternate Enable Output

5. Marker Output

6. Retrace Blanking Output

7. Low Alternate Sweep Output

8. Chassis Ground

9. -

10. Sweep Dwell Output

11. Lock Status Output

12. Penlift

13. External Trigger Input

14. V/GHz Output

15. End-of-Sweep Input

16. End-of-Sweep Output

17. -

18. Sweep Dwell Input

19. -

20. Bandswitch Blanking Output

21. Master Reset

22. Horizontal Sweep Input

23. Horizontal Sweep Input Return

24. Chassis Ground

25. Memory Sequencing Input

Ordering Information

Models

MG3691C 2 GHz - 10 GHz Signal Generator

MG3692C 2 GHz - 20 GHz Signal Generator

MG3693C 2 GHz - 31.8 GHz Signal Generator

MG3694C 2 GHz - 40 GHz Signal Generator

MG3695C 2 GHz - 50 GHz Signal Generator

MG3697C 2 GHz - 67 GHz Signal Generator (operational to 70 GHz)

Options and Accessories

MG3690C/1A Rack Mount with slides – Rack mount kit containing a set of track

slides (90 degree tilt capability), mounting ears, and front panel

handles to let the instrument be mounted in a standard 19-inch

equipment rack.

MG3690C/1B Rack Mount without slides – Modifies rack mounting hardware

to install unit in a console that has mounting shelves. Includes

mounting ears and front panel handles.

MG3690C/2A Mechanical Step Attenuator – Adds a 10 dB/step attenuator.

MG3690C/2B Rated RF output power is reduced. (This option comes in

MG3690C/2C different versions, based on instrument configuration)

MG3690C/2E Electronic Step Attenuator – Adds a 10 dB/step electronic attenuator

with a 120 dB range for the MG3691C. Rated RF output power

is reduced. (Not available with Option 20 or 22)

MG3690C/3 Ultra Low Phase Noise – Adds new modules to significantly reduce

SSB phase noise. (Not available with Option 3X)

MG3690C/3X Premium Phase Noise, improves Option 3 (< 1 kHz offset).

(Not available with Option 3)

MG3690C/4 8 MHz to 2.2 GHz RF coverage, Ultra-Low Phase Noise

version – Uses a digital down converter to significantly reduce

SSB phase noise. All specifications apply ≥ 10 MHz.

MG3690C/5 8 MHz to 2 GHz RF coverage – Uses an analog down converter.

All specifications apply ≥ 10 MHz.

MG3690C/6 Analog Sweep Capability – (limited to ≥ 500 MHz when used

with Option 4)

MG3690C/7 IF Up-Conversion – Adds an internal 40 GHz mixer for up-converting

an IF signal. (Not available with MG3695C, MG3696C, or

with Options 18 or 20)

MG3690C/8 Power Monitor – Adds internal power measurement capability.

(Not available with Option 9)

MG3690C/9K Rear Panel Output – Moves the RF output connector to the rear

MG3690C/9V panel. (This option comes in different versions, based on instrument

configuration) (Not available with Option 8)

MG3690C/10 User-Defined Modulation Waveform Software – External software

package provides the ability to download user-defined waveforms

into the memory of the internal waveform generator, serially or via

GPIB. External PC and an instrument with LF Generator, Option 27,

are required.

MG3690C/12 Frequency and Phase Modulation – External, via a rear panel BNC

connector. For internal modulation capability, requires additionally

LF Generator, Option 27.

MG3690C/14 Amplitude Modulation – External, via a rear panel BNC connector.

For internal modulation capability, requires additionally

LF Generator, Option 27.

MG3690C/15A High Power – Adds high-power RF components to the instrument

MG3690C/15B to increase its output power level.

MG3690C/15C (This option comes in different versions, based on instrument

MG3690C/15D configuration)

MG3690C/16 High Stability Time Base – Adds an ovenized, 10 MHz

crystal oscillator as a high-stability time base.

MG3690C/17 Delete Front Panel – Deletes the front panel for use in remote

control applications where a front panel display and keyboard control

are not needed. (Only available with Options 1A or 1B)

MG3690C/18 mmW Bias Output – Adds a rear panel BNC Twinax connector

required to bias the 63850 series millimeter wave source modules,

sold separately. Includes DC bias cable. (Not available with

Option 7 or 15x)

MG3690C/20 Scan Modulation – Adds an internal Scan modulator for

simulating high-depth amplitude modulated signals. Requires an

external modulating signal input capability. (Not available on models

MG3693C, MG3694C, MG3695C, MG3696C, or with Options 2E,

7, 15X, or 22)

MG3690C/22 0.1 Hz to 10 MHz Audio coverage – Uses a DDS for coverage down

to approximately DC. When adding Option 22, the output power is

derated by 2 dB. The frequency resolution below 10 MHz is 0.02 Hz.

No modulation is available in the 0.1 Hz to 10 MHz band.

(Not available without Option 4 or 5, or with Option 20 or 2E)

MG3690C/26A Pulse Modulation – External, via a rear panel BNC connector.

MG3690C/26B For internal modulation capability, requires additionally Pulse

Generator, Option 27. (This option comes in different versions,

based on instrument configuration)

MG3690C/27 Internal LF and Pulse Generators – Provides modulation waveforms

for internal AM, FM, ΦM and Pulse. (Not available without

Option 12, 14, or 26)

MG3690C/28A Analog Modulation Suite – For ease of ordering and package

MG3690C/28B pricing, this option bundles Options 12, 14, 26 and 27, offering

internal and external AM, FM, ΦM, and Pulse Modulation.

(This option comes in different versions, based on

instrument configuration)

Millimeter Wave Accessories

(Option 18 recommended for DC bias)

63850-15 50 GHz - 75 GHz V band Multiplier Source Module, WR-15

63850-12 60 GHz - 90 GHz E band Multiplier Source Module, WR-12

63850-10 75 GHz - 110 GHz W band Multiplier Source Module, WR-10

63850-08 90 GHz - 140 GHz F band Multiplier Source Module, WR-08

63850-06 110 GHz - 170 GHz D band Multiplier Source Module, WR-06

63850-05 140 GHz - 220 GHz G band Multiplier Source Module, WR-05

63850-03 220 GHz - 325 GHz H band Multiplier Source Module, WR-03

806-121 SMA male-male flexible cable, 90 cm (3 ft) (could be used to

connect the MG3690C output to the module's LO input)

Accessories

34RKNF50 DC to 20 GHz, Ruggedized Type N female adapter for units with

a K connector output

ND36329 MASTER/SLAVE interface cable set

63270 Transit case (16 kg, 66 cm x 41 cm x 81 cm, roll-away on four wheels)

2300-469 IVI Driver, includes LabView

driver

806-97 Aux I/O Cable, 25 pin to BNC: Provides BNC access to

Aux I/O Data Lines: Sequential Sync, Marker Out, Bandswitch

Blanking, Retrace Blanking, Sweep Dwell In, V/GHz, Horizontal Out.

Upgrades

Economical upgrades are available to upgrade any model to any higher performing

model. Consult Anritsu for details.