TK55253.FeederMaintenanceNotice.pdf - 第20页
Product Engineering Division SMT Sect ion Robotics Operations Y AMAHA MOTOR CO., L TD. MDOC-SOFT50282 21/ 21 T able 4.5 Recommend ed Drive Count for T ape Guide Maintenanc e (Recomme nded cycle for feeder maintenance) ▲ …
Product Engineering Division
SMT Section
Robotics Operations
YAMAHA MOTOR CO., LTD.
MDOC-SOFT50282
20/21
Table 4.4 Recommendation of Feeder MACS Correction Value/Pickup Error Rate
(Recommended cycle of feeder maintenance)
▲2
Notice Correct
(mm)
Stop Correct (mm) Notice
Pickup Err
Rate (%)
Stop Pickup
Err Rate (%)
Tape Type X Y X Y
4mm tape 0.200 mm 0.200 mm 0.000 mm 0.000 mm 1.00 % 0.00 %
8mm tape
12mm/16mm tape Not
supported
Not
supported
Not
supported
Not
supported
24mm tape
32mm tape
44mm tape
56mm tape
72mm tape
88mm tape
104mm tape
120mm tape
136mm tape
152mm tape
168mm tape
184mm tape
200mm tape
- Recommended value is common between SS feeder and ZS feeder.
Product Engineering Division
SMT Section
Robotics Operations
YAMAHA MOTOR CO., LTD.
MDOC-SOFT50282
21/21
Table 4.5 Recommended Drive Count for Tape Guide Maintenance (Recommended cycle
for feeder maintenance)
▲3
Notice Drive Cnt After
Tape Guide Maintenance
(10,000times)
Notice Drive Cnt After Tape
Guide Maintenance
(10,000times)
Tape Type SS Feeder ZS Feeder SS Feeder ZS Feeder
4mm tape Not
supported
Not
supported
Not
supported
Not
supported
8mm tape 30000
*10,000
times
36000 *
10,000 times
12mm/16mm tape Not
supported
Nott
supported
24mm tape
32mm tape
44mm tape
56mm tape
72mm tape
88mm tape
104mm tape
120mm tape
136mm tape
152mm tape
168mm tape
184mm tape
200mm tape
※ “Drive Cnt After Tape Guide Maintenance” for auto-loading feeders should be set as
8mm ZS feeder.
5. Limitation
This function has the following limitations.
1. While a special function “Feeder Maintenance Warning (Tok1183)” is used, this function
does not work.
2. When you use maintenance notice based on pickup error rate, it is recommended to set
[Server Path]. If [Server Path] is not set, the log is not taken over at power OFF/ON or
shared among other machines.
Product Engineering Division
SMT Section
Robotics Operations
YAMAHA MOTOR CO., LTD.
MDOC-SOFT50282
21/21
Table 4.5 Recommended Drive Count for Tape Guide Maintenance (Recommended cycle
for feeder maintenance)
▲3
Notice Drive Cnt After
Tape Guide Maintenance
(10,000times)
Notice Drive Cnt After Tape
Guide Maintenance
(10,000times)
Tape Type SS Feeder ZS Feeder SS Feeder ZS Feeder
4mm tape Not
supported
Not
supported
Not
supported
Not
supported
8mm tape 30000
*10,000
times
36000 *
10,000 times
12mm/16mm tape Not
supported
Nott
supported
24mm tape
32mm tape
44mm tape
56mm tape
72mm tape
88mm tape
104mm tape
120mm tape
136mm tape
152mm tape
168mm tape
184mm tape
200mm tape
※ “Drive Cnt After Tape Guide Maintenance” for auto-loading feeders should be set as
8mm ZS feeder.
5. Limitation
This function has the following limitations.
1. While a special function “Feeder Maintenance Warning (Tok1183)” is used, this function
does not work.
2. When you use maintenance notice based on pickup error rate, it is recommended to set
[Server Path]. If [Server Path] is not set, the log is not taken over at power OFF/ON or
shared among other machines.