80S-2080F480F4-680F5 User’s Manual.pdf - 第45页
SIPLACE 80S-20/F4/F4-6/F5 User’s Manual 1 Operational Safety Edition 03/98 f rom SW SR.404.xx 1.1 Information on safety 1 - 3 1.1 Information on safety 1.1.1 Convention for the use o f danger symbols These oper ating in …
1 Operational Safety SIPLACE 80S-20/F4/F4-6/F5 User’s Manual
Edition 03/98 from SW SR.404.xx
1 - 2
SIPLACE 80S-20/F4/F4-6/F5 User’s Manual 1 Operational Safety
Edition 03/98 from SW SR.404.xx 1.1 Information on safety
1 - 3
1.1 Information on safety
1.1.1 Convention for the use of danger symbols
These operating instructions contain notes that must be observed to guarantee your personal safety and to
avoid damage to equipment. The notes are highlighted by warning triangles and are indicated as follows
according to the level of risk:
DANGER or
within the intention of this user’s manual means that serious injury, death or considerable damage to property
will result
if the notes relating to danger are not observed.
WARNING or
within the intention of this user’s manual means that serious injury, death or considerable damage to property
could result
if the warning notes are not observed.
CAUTION or
within the intention of this user’s manual means that light injury or damage to property can result if the caution
notes are not observed.
NOTE
within the intention of this user’s manual provides important information concerning the product or that part of
the user’s manual to which particular attention is to be drawn.
1.1.2 Qualified personnel
Qualified or adequately trained personnel means that these people are familiar with the setting up, operation
and maintenance of automatic placement systems and add-on devices and have an appropriate qualification,
such as:
- Training or instruction or authorization to switch on or off, isolate, ground or label circuits and parts of the
installation in accordance with safety standards.
- Training or instruction in accordance with safety standards in the care and use of appropriate safety equip-
ment.
- Training in first aid.
1 Operational Safety SIPLACE 80S-20/F4/F4-6/F5 User’s Manual
1.1 Information on safety Edition 03/98 from SW SR.404.xx
1 - 4
1.1.3 Use as prescribed
WARNING
The product must only be used for the applications specified in the catalogs and technical descriptions, and
then only in conjunction with non-Siemens devices and components that have been approved by Siemens.
For the product to operate correctly and reliably, it must have been transported, stored, erected and assem-
bled correctly and must be operated and maintained with care.
1.1.4 Operational safety
WARNING
In order to assure operational safety the following points must be observed without fail:
- NEVER open one of the two protective covers if you are not totally familiar with the sequence and function-
ing of the machine. Do not open the protective covers during operation unless you are told to do so in this
User Manual or in the station software dialog.
- The key switch must only be unlocked by trained and qualified personnel.
Do not release the key switch during operation unless you are told to do so in this User Manual or in the
station software dialog.
- Never bring your head or arms into the travel area of the gantry when a station is switched on!
- No modifications of any type whatsoever may be made where it is not absolutely clear what effect they
would have on the functioning of the unit as a whole!
- The stations may only be adjusted, converted or maintained by personnel trained in this!
- Only use original spare parts and authorized accessories from Siemens AG. Using other parts will impair
safety and may cancel any liability of Siemens AG for the consequences.
- The operating safety of the SMD placement machines can only be guaranteed when the SMD placement
machines are used properly and for the purpose intended and when the provisions of the user’s manual
are complied with.
- The machine key and the key for the key-operated switch must be kept so that only qualified personnel
have access to them!
- If it is necessary to work on the machine and you do not have enough trained personnel available in your
plant, always call in a service technician from Siemens AG. Siemens AG will not accept any claims for
damage or consequential damage that is the result of incorrect work.
- Machine operators must only carry out work for which they have been adequately trained and with which
they are totally familiar.
- You must also follow any special safety regulations applicable in your own country.