00196376-0102_UM S-Feeder_EN.pdf - 第21页
General Conventions for the Use of Hazard Symbo ls Safety Instructions User Manual SIPLACE S-Feeder 21 1.5 Safety Instructions 1.5.1 Conventions for the Use of Hazard Symbols This Operating Manual contains not es that mu…
General
Installing the Feeders Dip Modules
20 User Manual SIPLACE S-Feeder
1.3.4 Dip Modules
Operating the feeder
1.4 Installing the Feeders
A general description of how to install the feeders is provided in the operating manuals of the respective
placement machines.
For processing with conductive adhesive, which is applied to
the components during placement.
Item number: 00117010-xx
Processable component sizes:
On IC head
On 6 segment RV head
(old manual)
max. 36x36 mm
max. 13x13 mm
Location required on changeover table: 3x two 8 mm tracks
Possible locations: Track 7 to track 111
(track 7 and track 111 = center of DIP module)
The DIP module can be set up max. 1x per machine.
Possible layer thickness to be set: 25 μm to 75 μm (in 10 μm steps)
max. tolerance of gap height: +/- 10 μm, delivery state +/- 5 mm
Materials for processing: Flux (paste) with high viscous flow or conductive adhesive
Machine: All machines in the SIPLACE family (except X4i)
Station software: 4xx, 5xx, 6xx
SIPLACE Pro: From version 3.0
General
Conventions for the Use of Hazard Symbols Safety Instructions
User Manual SIPLACE S-Feeder 21
1.5 Safety Instructions
1.5.1 Conventions for the Use of Hazard Symbols
This Operating Manual contains notes that must be observed to guarantee your personal safety and to
avoid damage to equipment. This information is marked by a warning triangle and is classified as follows:
1.5.2 Qualified Personnel
Qualified or adequately trained personnel means that these people are familiar with the setting up,
operation and maintenance of placement machines and add-on devices and are suitably qualified, e.g.
▪ Have been trained, instructed or authorized to switch on and off, isolate, earth and identify electrical
circuits and system components in accordance with normal safety standards.
▪ Have been trained or instructed in the upkeep and use of appropriate safety equipment in accord-
ance with normal safety standards.
▪ Have received first aid training.
1.5.3 Correct Usage
DANGER
as used in this Operating Manual means that fatal injuries, severe injuries or considerable
damage to equipment will occur, if this hazard note is not followed.
WARNING
as used in this Operating Manual means that fatal injuries, severe injuries or considerable
damage to equipment can occur, if this warning is not followed.
CAUTION
as used in this Operating Manual means that minor injuries or damage to equipment may occur
if this caution note is not followed.
NOTICE
as used in this Operating Manual provides information about the product or indicates a part of
the Operating Manual that requires particular attention.
WARNING
Type and source of the danger
The product may only be used for its intended purposes as described in the catalogs and tech-
nical descriptions and only with the third-party equipment and components recommended or
permitted by ASM Assembly Systems.
The proper and safe operation of the product requires correct transportation, storage, installa-
tion and assembly, plus careful, accurate utilization and servicing.
General
Safety Instructions Incorrect Usage
22 User Manual SIPLACE S-Feeder
1.5.4 Incorrect Usage
Failure to use the product as prescribed can result in both danger to life and limb and material damage.
For this reason any use that is not prescribed is not allowed. If the product is not used as prescribed,
ASM Assembly Systems accepts no liability for any damage that may occur and does not guarantee that
the components will work properly and without problems.
Failure to use the product as prescribed includes, for example:
▪ Placement of components that do not meet the permitted specification.
▪ The use on other machines than those machine types officially approved by ASM Assembly Systems
for this product.
▪ The use of the product in a working environment which deviates from that described in this manual.
▪ Use of the placement machine by unqualified personnel.