00192801-01.pdf - 第36页
3 Assembling and installing User Manual V 1.15 - Productivity Lift 3.3 Switching the devic e on Software version V 40. 1 1 Edition 01/2001 28 6Z LWFKLQJWKHG HY LFHRQ Once the dev ice ha s been switc hed on at the …
User Manual V 1.15 - Productivity Lift 3 Assembling and installing
Software version V 40.11 Edition 01/2001 3.1 Power supply 230V/50Hz or 110V/60Hz
27
$VVHPEOLQJDQGLQVWDOOLQJ
:$51,1*
Work on a system that is not (yet) properly service engineers from the manufacturing company
may only carry out set up.
127(
For assembling and maintenance refer to the existing Installation and Maintenance Manual.
3RZHUVXSSO\9+]RU9+]
The machines can be operated using two different power supplies. By changing the wiring of the
power supply PSU 500L24 the appropriate power setting can be adjusted. Please refer to the cir-
cuit diagrams.
,QVWDOODWLRQDQGRSHUDWLRQLQVWUXFWLRQV
For the installation and operation of the productivity lift the following advises have to be observed:
1. Area load allowed for undercover 0,2 t/m²
2. Room temperature 15°C to 35°C
3. Humidity in the area 30% to 70%
4. Average humidity ≥ 45%
3 Assembling and installing User Manual V 1.15 - Productivity Lift
3.3 Switching the device on Software version V 40.11 Edition 01/2001
28
6ZLWFKLQJWKHGHYLFHRQ
Once the device has been switched on at the main switch, an emergency stop message appears
in the display, which must be confirmed using the "Enter" key. This will set the device to the stand-
by-operating mode.
Pressing the "Start" key sets the device to the automatic operating mode, which begins by running
an initialisation phase. This serves to test basic system functions.
Following this brief initialisation, the device is set to the automatic operating mode and is ready to
operate.
,QVWDOODWLRQ5HLQVWDOODWLRQRIHPHUJHQF\FRQYH\RU
The emergency conveyor is used, when the shuttle is not in use e.g. for reasons of maintenance.
,QRUGHUWRDFWLYDWHWKHHPHUJHQF\FRQYH\RUGRWKHIROORZLQJ
1. By pushing the "stop" cursor the corresponding conveyor is put into stand-by mode.
2. Through "ALT" cursor the adjustment mode comes up.
3. Through the "Enter" cursor the menu comes up on the display which shows "PCB takeover"
comes up and you can check if the adjustment is "dual lane". If this is not the case one can
switch to "dual lane" as described in the chapter 6.3.
4. Use the "enter" cursor. The menu "PCB transfer" comes up. Here it is the same procedure as
described in point 3 (see chapter "6.6").
5. Another use of the "enter" cursor brings up the menu "PCB pass-through". In this menu the
emergency conveyor can be switched on by choosing the adjustment "switched on" (see chap-
ter "6.7"). This change can be taken over with the "enter" cursor.
6. The adjustment mode can be quit with the "stop" cursor.
If the machine is started now the lift conveyor drives down and the emergency conveyor lowers to
the operating position and starts itself. Afterwards the device is again in operation mode.
User Manual V 1.15 - Productivity Lift 3 Assembling and installing
Software version V 40.11 Edition 01/2001 3.4 Installation / Reinstallation of emergency conveyor
29
6WRSRIHPHUJHQF\FRQYH\RU
7RVWRSWKHHPHUJHQF\FRQYH\RUWKHSURFHGXUHGHVFULEHGDERYHKDVWREHPDGHWKHRWKHU
ZD\URXQG
1. By pushing the "stop" cursor the corresponding conveyor is put into stand-by mode.
2. Through "ALT" cursor the adjustment mode comes up.
3. Through the "Enter" cursor the menu comes up on the display which shows "PCB takeover"
comes up and you can chose the adjustment as used before the emergency conveyor (see
chapter "6.3").
4. Use the "enter" cursor. The menu "PCB transfer" comes up. Here it is the same procedure as
described in point 3 (see chapter "6.6").
5. Another use of the "enter" cursor brings up the menu "PCB pass-through". In this menu the
emergency conveyor can be switched off by choosing the adjustment "switched off" (see chap-
ter "6.7"). This change can be taken over with the "enter" cursor.
6. The adjustment mode can be quit with the "stop" cursor.
The device can be started with the "start" cursor. After an initialising time the device is ready for
operation.
127(
Pay attention that the changes made in chapter 6.3 and 6.6 are set back to the adjustments as
before activated.