00900330-01_UM_ASM-ProcessLens_EN.pdf - 第78页

5 Working with the machine 5.1 Controls and displays 78 Instruction manual ASM ProcessLens 03/2021 DANGER Death, serious injury or considerable damage may result if these machines are handled incorrectly ► Always follow …

5 Working with the machine

5.1 Controls and displays

Instruction manual ASM ProcessLens 03/2021 77

Condition Possible states Frequency of flashes

Green On

Off

Pulse

Pulse Frequency (ms)

Amber On

Off

Pulse

Pulse Frequency (ms)

Red On

Off

Pulse

Pulse Frequency (ms)

Buzzer On

Off

Pulse Frequency (ms)

LCD monitor

(see fig. "Controls and displays" [}76])

There is a flat LCD monitor at the front side of the ASM ProcessLens machine. A LCD monitor with

a touch-sensitive surface (touchscreen) as an option is available.

Keyboard

(see fig. "Controls and displays" [}76])

The keyboard and mouse are located beneath the monitor.

CAUTION

Risk of collision of personnel with monitor and keyboard holder

Risk of collision of the front hood with the arm where the monitor, keyboard and mouse are

mounted.

Key switch ON/OFF

(see fig. "Controls and displays" [}76])

Turn on the control power manually and switch the conveyor into pass through mode when the PC

is down.

► Close the GUI program.

► Switch off the machine by the main switch.

► Wait for 30 sec and then switch on the machine at the main switch.

► Turn the key switch to the left and release to turn on the control power.

► Turn the key switch to the right.

The conveyor set to pass through running mode.

Main power switch in ON position

(see fig. "Controls and displays" [}76])

After switching on the main power switch, 24 V DC and 240 V AC are present.

Main power switch in OFF position

(see fig. "Controls and displays" [}76])

The main power switch disconnects the single phase from the power supply.

5 Working with the machine

5.1 Controls and displays

78 Instruction manual ASM ProcessLens 03/2021

DANGER

Death, serious injury or considerable damage may result if these machines are

handled incorrectly

► Always follow the applicable accident prevention and safety regulations (particularly

DIN EN 60204, part 1 or IEC 60204, part 1) and the safety regulations in your own

country.

► The safety door to the power supply must ONLY be opened by appropriately qualified

and trained personnel.

Power ON lamp

(see fig. "Controls and displays" [}76])

On: The main power switch is switched to ON position. Power is supplied to the power distribution

module.

Off: The input voltage is not present.

Start button, green

(see fig. "Controls and displays" [}76])

After switching on the main power switch and having started the inspection software press the start

button to set ASM ProcessLens into regular inspection mode. Do the same if the EMERGENCY

STOP had been engaged and is now released or if the protective hood had been opened and is

now closed.

Stop button, black

(see fig. "Controls and displays" [}76])

This button is used to stop the machine and will perform the following tasks:

●

Stop the production operations and puts the machine in idle mode.

●

The control power is still present.

The EMERGENCY STOP button is red and latches in the ON position when pressed. When you

press the EMERGENCY STOP button, the switching contact of safety interlock module opens.

The signaling contact of the EMERGENCY STOP button opens.

The inspection cycle is interrupted and can then either be continued or cancelled once the machine

is working correctly again.

NOTICE

ASM ProcessLens electrical diagrams

For details, please refer to the ASM ProcessLens electrical diagrams.

Release the EMERGENCY STOP button

●

Release the EMERGENCY STOP button from latched position after being activated.

●

Operator can press the START button, to resume production operation.

●

The software sequence for START button as follows:

– Software will check that the hood is closed and EMS is not activated.

– Software will lock the door and reset the safety relay.

– Software will check that the safety relay interlock is cleared and enable the motors.