XP Type II 工程师培训手册 (2.0).pdf.pdf - 第199页
FK-9F98-34 XP Series T ype II T raining T ext for Service Engineers Edition 2.0 XP242E – Chapter 8 T ype II MTU Adjustment Page 6 of 18 8. Set the dial gage to 0 on the tray p allet jig as shown below: Adjust the cylinde…
FK-9F98-34 XP Series Type II Training Text for Service Engineers
Edition 2.0 XP242E – Chapter 8 Type II MTU Adjustment Page 5 of 18
eccentric pin. Adjust so that the dial gage reads 0 at the top of the pusher and 0 at the
bottom. Also measure the points in between, tolerance is +/-0.15mm
Fixing Bolts
Eccentric Pin
Fulcrum Pin
8.9 Tray Pusher Adjustment 2
1. Reverse the I/Os set in the previous adjustment. Turn Y032 TrayPusherFwd OFF, and
Y033: TrayPusherBwd ON.
2. Set the T axis 3mm below the + limit.
3. Set the tray pallet jig (Z9631DEPJ3740) in the magazine top slot, and set a magnet on
the underside. Confirm that the tray pallet jig is in contact with the guide bar.
4. Set the large block jig (Z9631ADEPJ8172) in slot [41,42].
5. Set the dial stand on the block jig and the dial gage to 0 on the magnet as shown below:
6. Descend the T-axis and watch the dial gage to find the position where the guide bar is
most forward.
7. Bring the T-axis back to 3mm below the + limit and set the tray pallet jig in the slot that is
in the position where the guide bar is most forward.
Fuji Machine Mfg. Co., Ltd. Okazaki
SMT Equipment Quality Assurance Dept.
8 – 5 CS Section
FK-9F98-34 XP Series Type II Training Text for Service Engineers
Edition 2.0 XP242E – Chapter 8 Type II MTU Adjustment Page 6 of 18
8. Set the dial gage to 0 on the tray pallet jig as shown below:
Adjust the cylinder stroke
so that when the pusher is
activated the tray pallet is
pushed 0.5mm.
9. Turn I/O TrayPusherBwd OFF, and I/O Y032 TrayPusherFwd ON to bring the pusher to
its forward position. The dial gage should indicate that the tray pallet jig has moved
0.5mm forward. If not it is necessary to adjust the cylinder stroke at the back of the MTU:
10. Move the tray pusher forward and find the position where the forward end sensor (X03E:
TrayPusherFwChk) first comes ON. From this position set the sensor a further 0.5mm in
the ON direction.
11. Move the tray pusher backward and find the position where the backward end sensor
(X03F TrayPusherBwChk) first comes ON. From this position set the sensor a further
0.5mm in the ON direction.
Fuji Machine Mfg. Co., Ltd. Okazaki
SMT Equipment Quality Assurance Dept.
8 – 6 CS Section
FK-9F98-34 XP Series Type II Training Text for Service Engineers
Edition 2.0 XP242E – Chapter 8 Type II MTU Adjustment Page 7 of 18
8.10 Shuttle Clamping Position Adjustment
1. Turn I/O Y032: TrayPusherFwd OFF and Y033: TrayPusherBwd ON to retract the tray
pusher.
2. Temporarily set the U-axis to 529mm.
3. Turn the tray catch stopper (see chapter 2.5 “Setting the Plus Software Limits” for
location of the tray catch stopper) until the distance from the clamper to the plate is
14mm, as illustrated below:
14mm
4. Bring the T-axis to 3mm below the + limit and set the tray pallet jig in slot [41,42].
5. Bring the tray pallet jig to the position where the guide bar is most forward (see step 8.9).
6. Turn I/O Y033: TrayPusherBwd OFF, and Y032 TrayPusherFwd ON to push the tray jig
0.5mm forward. Afterwards turn Y032: TrayPusherFwd OFF, and Y033 TrayPusherBwd
ON to retract the tray pusher.
7. Bring the tray pallet jig to the tray origin position for slot [41,42]. To calculate the tray
origin position subtract 200mm from the [T_TrayOrg] position found in [Maintenance C] –
[Proper Data Editor] – [TRAY] – [T_TrayOrg]. 200mm represents the 50mm pitch
between slots, times the number of slots from the [T_TrayOrg] position, in this case 4.
8. Place a magnet on the tray pallet and set a dial gage to 0 on the magnet as shown
below:
9. Jog the U-axis in the direction of the – (minus) mechanical stopper until the tray pallet is
clamped.
Fuji Machine Mfg. Co., Ltd. Okazaki
SMT Equipment Quality Assurance Dept.
8 – 7 CS Section