Error Code List.pdf - 第61页
AV131 ERROR CODE LIST 2.4 Errors D79EEC- 91-210-A 0 2.4- 38 2669 Cance l replace m ent c ompletion i nput (never ope n re ar right c over) DESCRI PTIO N Pa r t r ep l ac em en t com pl eti o n in pu t wa s c a n c el ed.…
AV131
ERROR CODE LIST
2.4 Errors
D79EEC-91-210-A0
2.4-37
2659
Rear upper cover safety detection
DESCRIPTION
The machine became a safety stop condition by the safety detection in the rear upper cover.
CAUSE
The cover of the rear upper has been opened.
SOLUTION
Press [Return] after closing the cover. Then please release the safety stop condition to push <Start> with
<ENABLING>.
NOTE
2663
Cancel replacement completion input (open rear left cover)
DESCRIPTION
Part replacement completion input was canceled.
CAUSE
Rear left cover was opened.
SOLUTION
Please close the rear left cover then input part replacement completion switch again.
NOTE
2664
Cancel replacement completion input (open rear right cover)
DESCRIPTION
Part replacement completion input was canceled.
CAUSE
Rear right cover was opened.
SOLUTION
Please close the rear right cover then input part replacement completion switch again.
NOTE
2665
Cancel replacement completion input (float left feeder)
DESCRIPTION
Part replacement completion input was canceled.
CAUSE
Feeder in the left part supply floats.
SOLUTION
Please confirm feeder condition then input part replacement completion switch again.
NOTE
2666
Cancel replacement completion input (float right feeder)
DESCRIPTION
Part replacement completion input was canceled.
CAUSE
Feeder in the right part supply floats.
SOLUTION
Please confirm feeder condition then input part replacement completion switch again.
NOTE
2668
Cancel replacement completion input (never open rear left cover)
DESCRIPTION
Part replacement completion input was canceled.
CAUSE
Part replacement completion operation was done without opening the rear left cover.
SOLUTION
Please close the cover after opening the cover once then input part replacement completion switch again.
NOTE
AV131
ERROR CODE LIST
2.4 Errors
D79EEC-91-210-A0
2.4-38
2669
Cancel replacement completion input (never open rear right cover)
DESCRIPTION
Part replacement completion input was canceled.
CAUSE
Part replacement completion operation was done without opening the rear right cover.
SOLUTION
Please close the cover after opening the cover once then input part replacement completion switch again.
NOTE
2670
Insertion error (Neither lead detection)
DESCRIPTION
Insertion error was detected. Neither of two leads of the part was detected to have been inserted.
CAUSE
Refer to “DETAILED DESCRIPTION”.
SOLUTION
Take appropriate action according to “DETAILED DESCRIPTION”.
Close the error screen and remove the part concerned.
Refer to the pop-up guidance displayed on the screen for how to continue/resume production.
DETAILED DESCRIPTION
Probable causes and actions to be taken are as follows:
Improper handover position from the rotary chuck to the slide chuck. Adjust the stroke and position of the slide
chuck.
Nonsmooth piston movements of the slide chuck Apply oil to the piston.
Damaged or bent rotary chuck Replace the rotary chuck.
Gap in the closed rotary chuck Replace the rotary chuck if the gap is 0.1 mm or more.
Part lead bent more than the specification Use a part that conforms to the specifications.
Nonsmooth part feed in the feeder due to taping width narrower than the specification. Use a part that conforms
to the specifications.
Nonsmooth part feed in the feeder due to taping width wider than the specification. Use a part that conforms to
the specifications.
Loose parts taping Use a part that conforms to the taping strength of the specifications.
Incomplete cartridge/feeder setting Check that the feeder and cartridge have been properly set in position.
Improper part pulling position of the rotary chuck Adjust the transfer chuck unit and feed unit.
Nonsmooth rotary chuck opening/closing Apply oil to the swing unit and sliding unit.
Air leaking due to damaged or cracked air hose Replace the hose.
Bent slide chuck block Replace the block.
Worn tape cutter blade Replace the blade.
Improperly adjusted tape cutter blade position Adjust the extension of the blade.
The machine is stopped due to insertion error even when parts have been exhausted. (Part detection sensor is
always ON.) Clean and adjust the part detection sensor.
NOTE
AV131
ERROR CODE LIST
2.4 Errors
D79EEC-91-210-A0
2.4-39
2671
Insertion error (No right lead detection)
DESCRIPTION
Insertion error was detected. Right lead of the part was not detected to have been inserted.
CAUSE
Refer to “DETAILED DESCRIPTION”.
SOLUTION
Take appropriate action according to “DETAILED DESCRIPTION”.
Close the error screen and remove the part concerned.
Refer to the pop-up guidance displayed on the screen for how to continue/resume production.
DETAILED DESCRIPTION
Probable causes and actions to be taken are as follows:
Worn pusher and bending die Replace if worn.
Gap between the pusher and bending die is larger than the reference value. Readjust the gap.
Gap between the bending die and insertion guide is larger than the reference value. Readjust the gap.
PCB hole and insertion unit not aligned even after recognition. Check the rotation offset and camera offset.
Mismatch of size between the reference pin and PCB Use a reference pin with proper size.
Rail width wider than the reference value. Set the width of PCB to +0.05 mm.
Worn insertion unit and cutter or improper adjustment of gap between them Replace the unit or adjust the gap.
Width of the insertion guide at origin is outside the reference value. Return the WH axis to its origin.
Hole diameter is smaller than the lead diameter. Correct the relationship between the lead and hole diameters.
Inappropriate line diameter and pitch data Enter the correct values.
Off-centered insertion guide Perform centering of the insertion unit.
The machine is stopped due to insertion error even when parts have been exhausted. (Part detection sensor is
always ON.) Clean and adjust the part detection sensor.
NOTE
2672
Insertion error (No left lead detection)
DESCRIPTION
Insertion error was detected. Left lead of the part was not detected to have been inserted.
CAUSE
Refer to “DETAILED DESCRIPTION”.
SOLUTION
Take appropriate action according to “DETAILED DESCRIPTION”.
Close the error screen and remove the part concerned.
Refer to the pop-up guidance displayed on the screen for how to continue/resume production.
DETAILED DESCRIPTION
Probable causes and actions to be taken are as follows:
Worn pusher and bending die Replace if worn.
Gap between the pusher and bending die is larger than the reference value. Readjust the gap.
Gap between the bending die and insertion guide is larger than the reference value. Readjust the gap.
PCB hole and insertion unit not aligned even after recognition. Check the rotation offset and camera offset.
Mismatch of size between the reference pin and PCB Use a reference pin with proper size.
Rail width wider than the reference value. Set the width of PCB to +0.05 mm.
Worn insertion unit and cutter or improper adjustment of gap between them Replace the unit or adjust the gap.
With of the insertion guide at origin is outside the reference value. Return the WH axis to its origin.
Hole diameter is smaller than the lead diameter. Correct the relationship between the lead and hole diameters.
Inappropriate line diameter and pitch data Enter the correct values.
Off-centered insertion guide Perform centering of the insertion unit.
The machine is stopped due to insertion error even when parts have been exhausted. (Part detection sensor is
always ON.) Clean and adjust the part detection sensor.
NOTE