SOM-2080-001_w.pdf - 第131页

128 SOM-2080 Erroe ID Error Name, Description, Cause, and Remedy 4b2713 Start Process(Feeder Connect Error) There is a splicing failure feeder. ----- 4b2721 Start Process(Feeder Connect Error) The reel list check is not …

100%1 / 179
127
SOM-2080
6.11 Others
1005-001
Erroe ID Error Name, Description, Cause, and Remedy
4b2426 Feeder (Movement Error)
Alarm Code:E5 - Redundant Order Error
-----
4b2427 Feeder (Movement Error)
Alarm Code:E6 - Timeout Error in Changing Servo Motor Axis
-----
4b2428 Feeder (Movement Error)
Alarm Code:E7 - Servo ON Timeout
-----
4b24a1 Feeder (Movement Error)
An error occurred before the feeder operation.
-----
4b24a2 Feeder (Movement Error)
An error occurred in the feeder operation.
-----
4b24a3 Feeder (Movement Error)
Feeder error (feeding time-out)
-----
4b2501 Failed Splicing Operation
Alarm Code:E3 - (1)No supplied history/ (2)Dirty splicing detection sensor (dust
adhesion)
(1) Please operate to resupply components in the machine after splicing
operation./ (2) Please clean the joint detection sensor.
4b2601 Unit PCB BBR Information
There is no information in the relevant PCB (on the Transfer Conveyor).
Delete the BBR information after removing the P.C.B..
4b2602 Unit PCB BBR Information
There is no information in the relevant PCB (on the Transfer XY-Table).
Delete the BBR information after removing the P.C.B..
4b2603 Unit PCB BBR Information
A problem was found in the unit PCB BBR information.
Delete the BBR information after removing the P.C.B..
4b2701 Start Process(Feeder Connect Error)
A special feeder is appointed. Please confirm the model of a set feeder.
-----
4b2702 Start Process(Feeder Connect Error)
A special feeder is set. Please confirm the model of a set feeder.
-----
4b2711 Start Process(Feeder Connect Error)
ACV Check Error. Component ID on the feeder is not same as one specified by
current program.
-----
4b2712 Start Process(Feeder Connect Error)
Set "enable" for destination alternate feeder.
-----
128
SOM-2080
Erroe ID Error Name, Description, Cause, and Remedy
4b2713 Start Process(Feeder Connect Error)
There is a splicing failure feeder.
-----
4b2721 Start Process(Feeder Connect Error)
The reel list check is not completed.
-----
4b2722 Start Process(Feeder Connect Error)
Feeder is not ready
-----
4b2731 Start Process(Feeder Connect Error)
Please turn on the Feeder Ready SW (rear).
-----
4b2732 Start Process(Feeder Connect Error)
Please turn on the Feeder Ready SW (front).
-----
4b2733 Start Process(Feeder Connect Error)
Please set the feeder (rear) that used by the pattern program.
-----
4b2734 Start Process(Feeder Connect Error)
Please set the feeder (front) that used by the pattern program.
-----
4b2735 Start Process(Feeder Connect Error)
Feeder communication not finish (rear)
Push the feeder ready sw(rear) OFF to ON
4b2736 Start Process(Feeder Connect Error)
Feeder communication not finish (front)
Push the feeder ready sw(front) OFF to ON
4b2801 2D BarCode Information
Socket Connection Error
-----
4b2802 2D BarCode Information
The communication of the barcode info. was not completed in prescribed time.
-----
4b2803 2D BarCode Information
An error response was received form the destination device of the barcode info.
-----
4b2804 2D BarCode Information
An error occurred in the sending process of the barcode info.
-----
4b2805 2D BarCode Information
Internal Processing Error
-----
6.11 Others
1005-001
129
SOM-2080
Erroe ID Error Name, Description, Cause, and Remedy
4b2901 Linear Scale Error
An error for the linear scale position occurred at the beam X-axis (rear) during
zeroing operation.
Please check the linear scale attaching position on the beam X-axis (rear).
4b2902 Linear Scale Error
An error for the linear scale position occurred at the beam X-axis (front) during
zeroing operation.
Please check the linear scale attaching position on the beam X-axis (front).
4b2903 Linear Scale Error
An error for the linear scale position occurred at the beam Y-axis (rear) during
zeroing operation.
(1) Check the linear scale on the beam Y-axis (rear).
(2) Check the linear scale attaching position on the Y1 and Y2.
(3) Check if the process of the linear scale origin mark on the Y1 and Y2 has an
error.
4b2904 Linear Scale Error
An error for the linear scale position occurred at the beam Y-axis (front) during
zeroing operation.
(1) Check the linear scale on the beam Y-axis (front).
(2) Check the linear scale attaching position on the Y1 and Y2.
(3) Check if the process of the linear scale origin mark on the Y1 and Y2 has an
error.
4b2905 Linear Scale Error
An error for the linear scale skip occurred at the beam Y-axis (rear) during zeroing
operation.
Please confirm if the linear scale on the beam Y-axis (rear) has flaws and soil.
4b2906 Linear Scale Error
An error for the linear scale skip occurred at the beam Y-axis (front) during
zeroing operation.
Please confirm if the linear scale on the beam Y-axis (front) has flaws and soil.
4b2907 Linear Scale Error
An error for the linear scale parallel offset deviation occurred at the beam Y-axis
(rear) during zeroing operation.
Please check the linear scale attaching condition on the beam Y-axis (rear).
4b2908 Linear Scale Error
An error for the linear scale parallel offset deviation occurred at the beam Y-axis
(front) during zeroing operation.
Please check the linear scale attaching condition on the beam Y-axis (front).
4b2a01 Splicing No Check Error
The seam reached the pick-up position as unregistered splicing. Please replenish
the component.
-----
4b2b01 Label Feeder
The pick-up section in the label feeder (rear) is not set correctly.
Reset the pickup section in the label feeder correctly.
6.11 Others
1005-001