TS560R-USER-GUIDE.pdf - 第5页

28 Proceed to make changes Click OK button to save The new parameters will be displayed on the controller 7. SOFTWARE UPGRADE Note: For future software upgrade , follow the instructions below. 1. Download the latest soft…

2. SYMBOL DEFINITIONS

Symbol Description Symbol Description

Run (Activate)

Setup

Valve Pressure

Counter reset

Atomized Air

Pressure

Mac address

Timed mode

Accept change

Interrupt mode

Pressure calibration

Teach mode

Save

Purge mode

Reset time in Teach

mode

Spray

IP address

Pre-Spray

Post-Spray

Cancel

Run Method

Sequence Mode

Continous Mode

Sequence Continous

Mode

E-Stop

Change Password

Remote Server

On line

Off Line

6. Wait until the system completes the software update from the USB drive

and the first touch-screen calibration is displayed

7. Remove the USB drive from the USB port before proceeding to the next

step

8. Follow the instructions on the display to calibrate the touch screen by

touching the crosshair at five different points. Note: In order to

accurately calibrate the touch screen, it’s recommended that the stylus

pen is used

9. Wait until the system completes the rebooting sequence and the home

screen is displayed

10. Repeat sections 5.1.1 and 5.1.2 to re-calibrate the air pressure

Proceed to make changes

Click OK button to save

The new parameters will be displayed on the controller

7. SOFTWARE UPGRADE

Note: For future software upgrade, follow the instructions below.

1. Download the latest software version from Techcon website and copy it to

a blank USB thumb drive. Note: Do not put the software file inside a

folder

2. Make sure that the unit is turned off

3. Insert the USB drive to the USB port located in the back of the unit

4. Turn on the unit

5. Wait while the system is loading the new software. This process can take

a few minutes

“Edit” icon

TOUCH

SCREEN

ATOMIZED AIR

PORT

VALVE

ACTIVATION

PORT

WIFI ANTENNA

POWER

SWITCH

AIR INLET

AIR OUTLET

UNREGULATED

FOOT

SWITCH

PORT

POWER

INLET

IO PORT

INTERNET

PORT

USB PORT

GROUNDING

TS560R

3. SPECIFICATIONS

4. FEATURES

Figure 1.0

Size

290mm x 212mm x 98mm

(

11.4” X 8.3” X 3.9”

)

Weight 3.1 kg (6.8lbs)

Input Voltage 24VDC

Output Voltage Range 0-24 VDC

Rated Power 15W

Air Input 100 psi (6.9 bars) Max.

Air Output 0-99.9 Psi (6.9 bar)

Pollution Degree II

Installation Category I

Indoor Use Altitude up to 2,000m (6,562ft)

Operating Temperature 0˚C to 50˚C (32˚F to 122˚F)

Storage Temperature -10˚C to 60˚C (14˚F to 140˚F)

Max. Relative Humidity

80% for temperature up to 31˚C (87.8˚F) Decreasing

linearl

to 50% relative humidit

at 40˚C

(

104˚F

)

Timer 0.008-99.99 seconds

Cycle Mode Timed, Interrupt, Teach, Purge

Timing Repeat Tolerance +/- 0.001%

Cycle Rate 900 cycles/min

Display Touch Screen, Resitive

Meets or exceed CE, TUV and NRTL

TS560R

VALVE AIR HOSE

ATOMIZED AIR HOSE

TO AIR SOURCE

5. TO CONTROL SPRAY VALVE

CAUTION: A 5-micron filter (TSD800-6) must be installed with the unit to ensure proper

air filtration.

Figure 2.0

5.1 Connecting the Unit: (Refer to Figure 1.0 and 2.0)

1. Connect the power cord, foot switch to the back of the unit.

2. Connect Valve air hose to Port A (Not Regulated)

3. Connect Atomized air hose to Port B (Regulated)

4. Press the Power switch to turn on the unit.

Items Description

1 Air Filter

2 Valve (not included)

3 Pressure Pot (not included)

4 Display

5 Power Adapter

6 Foot Switch

6.2 Making Parameters Adjustment from the webserver

Go back to the webserver site and click on the “Controllers” menu

Click on the active controller link

The controller screen will be displayed in the webserver as shown below.

The controller parameters such as pressure and dispense time can be adjusted

from the webserver.

Click on the “Edit” icon

The parameter screen will appear as shown below: