00191134-03.pdf - 第215页

GEM for SIPLACE V5.01 ©Siemens AG, all rights r eserved page 215 of 252 CEID Nam e Descript ion range, invalid m easured value* 711055 FM_KOP_RESET Coplan: error upon reset* 1 711056 FM_KOP_VERSION Coplan: incor rect ver…

GEM for SIPLACE V5.01

CEID Name Description

711028 FM_CO_BEIN_ZUVIEL Coplan.: Too many pins measured* 1

711029 FM_CO_MEM_OVERFLOW Undefined error message 1

711030 FM_CO_KOMM_BUFFER_VOL

Message to coplanarity too long* 1

711031 FM_CO_MESSD_BUFFER_VO

Coplan.: Measuring data buffer is full* 1

711032 FM_CO_GRP_POOL_LEER Coplan.: Memory for group description

full*

711033 FM_CO_GF_POOL_LEER Coplan.: Memory for package form

description full*

711034 FM_CO_MATH_FEHLER Undefined error message 1

711035 FM_CO_DIV_NULL Coplan.: Division by zero* 1

711036 FM_CO_MESSBER_UNG Undefined error message 1

711037 FM_CO_BE_MESSBEREICH Coplan.: Component outside of

measuring range*

711038 FM_CO_BEIN_FEHLT Coplan.: One pin of component

missing*

711039 FM_CO_MESSDAT_UNVOLL Coplan.: Measuring on one pin

finished*

711040 FM_CO_BEIN_DEFEKT Coplan.: Pin outside of coplan.

position tolerance*

711041 FM_CO_AUSW_ABGEB Coplan.: Placement level not found* 1

711042 FM_CO_FF_FHL Undefined error message 1

711043 FM_CO_FF_FHL_CCD Coplanarity module defective; replace

and boot*

711044 FM_CO_FF_FHL_SCAN_STAR

Coplanarity module defective; replace

and boot*

711045 FM_CO_FF_FHL_SCAN_ENDE Coplanarity module defective; replace

and boot*

711046 FM_CO_FF_FHL_SKAL Coplanarity module defective; replace

and boot*

711047 FM_CO_FF_FHL_MAX_DIG Coplanarity module defective; replace

and boot*

711048 FM_CO_FF_FHL_C_CODE Software error in coplanarity module;

boot*

711049 FM_CO_EXIT_PROG Coplan.: Command Quit sent* 1

711050 FM_CO_BE_SCHLECHT Coplanarity: Bad component, to be

returned*

711051 FM_COPL_SPURLEER Track empty due to coplanarity error* 1

711052 FM_CO_N_MESSBAR component was not measured: offset

too big*

711053 FM_KOP_KOMM Coplan: communications error* 1

711054 FM_KOP_GROB Coplan: z-position outside measuring 1

GEM for SIPLACE V5.01

CEID Name Description

range, invalid measured value*

711055 FM_KOP_RESET Coplan: error upon reset* 1

711056 FM_KOP_VERSION Coplan: incorrect version* 1

711057 FM_KOP_DURCHM Coplan: incorrect diameter of

calibration tool*

711058 FM_KOP_KANTE Coplan: edge of calibration tool not

found*

* Depending on the collection event, some of the status variables <ERRORTYPE>,

<GANTRYONERROR>, <SEGMENTONERROR>, <TRACKONERROR>,

<ERRORINFO1> and <ERRORINFO2> will be updated at each of these coplanarity

collection events.

:DIIOH3DFN&KDQJHU

CEID Name Description

810001 WPCtrayChanged WPC tray changed 1

810002 WPCtransPos WPC in transport position 1

810003 WPCrefillPos WPC in refill position 1

810004 WPCrefillCheck WPC refill check finished 1

810005 WPCrefRun WPC reference run completed and

<SOFTWAREREVWPC> updated

810006 WPCsetUpLoad Setup loaded on WPC 1

810007 WPCinvetStatus <INVENTARYWPC> status received

form WPC

811001 FM_WPW_RIO Communication with wafflepack

changer faulty*

811002 FM_WAG_DUMMY_E0_OK undefined error number from trolley

(E0) *

811003 FM_WAG_CHECKSUMME Check sum error in communication

with table*

811004 FM_WP_SYNTAX Syntax error in command to

component table*

811005 FM_WAG_CODE_LOST Program loss of table or trolley

control*

811006 FM_WAG_RAM_DEFEKT RAM of trolley control defective* 1

811007 FM_WP_REFER Command not executed, component

table not referred*

811008 FM_WP_NACHF Command not executed, component

table in refill position*

811009 FM_WP_RAHMEN WPC: No tray available* 1

811010 FM_WP_RUESTUNG_Q WPC: Sent set-up contains errors* 1

811011 FM_WP_SPEICHER WPC: Data loss in component table 1

GEM for SIPLACE V5.01

CEID Name Description

(defective battery) *

811012 FM_WP_TIMEOUT_T WPC: Fault in feed axis (Servo or

axis card) *

811013 FM_WP_ENDSCH_T WPC: Feed axis at limit switch* 1

811014 FM_WP_ACHSE_T WPC: Axis error of feed axis* 1

811015 FM_WP_SCHALTER_T WPC: Feed axis servo released* 1

811016 FM_WP_ZANGE WPC: Error in jaw position* 1

811017 FM_WP_TIMEOUT_P WPC: Fault in lifting axis (Servo or

axis card) *

811018 FM_WP_ENDSCH_P WPC: Lifting axis at limit switch* 1

811019 FM_WP_ACHSE_P WPC: Axis error of lifting axis* 1

811020 FM_WP_SCHALTER_P WPC: Lifting axis servo released* 1

811021 FM_WP_STEUERUNG WPC: Control switched off* 1

811022 FM_WP_SCHUTZ WPC: Protection at component table

open*

811023 FM_WP_TRANSP WPC: Error while transporting tray* 1

811024 FM_WP_RUESTUNG WPC: Error in saved set-up* 1

811025 FM_WP_FEHLT WPC: One tray of saved set-up

missing*

811026 FM_WP_MAGAZIN WPC: When returning tray, level

occupied*

811027 FM_WP_VERSCHW WPC: Tray has been taken out* 1

811028 FM_WP_UEBERG WPC: Take-over position already

occupied*

811029 FM_WP_VERDREHT WPC: Tray in incorrect pos. or

protection not closed properly*

811030 FM_WP_SICHERUNG WPC: Feed axis has touched

protection*

811031 FM_WPW_NFPOS WPC must be moved from refill

position*

811032 FM_WP_WRITE_HD Error while writing WPC machine data

to hard disk*

811033 FM_WP_READ_HD Error while reading WPC machine

data from hard disk*

811034 FM_WP_WRITE_FD Error while writing WPC machine data

to floppy*

811035 FM_WP_READ_FD Error while reading WPC machine

data from floppy*

811036 FM_WP_ANSCHLAG limit switch not found* 1

811037 FM_WP_CHECKSUMME checksum error* 1

811038 FM_WPW error* 1

811039 FM_WP_NULLKORR distance between zero point of WPC 1