M6_ServiceManual_e.pdf - 第76页
4 Electrical Section 4-16 ■ Device 12 Address Bit No. Signal Name Addr ess Bit No. Signal Nam e 0000h 0 Device No. Bit0 0003h 0 MXR Pallet Bar Open1 / MX20 Pallet Interlock in Stocker 1 Device No. Bit1 1 MXR Pallet Bar O…

4 Electrical Section
4-15
■ Device 8
Address Bit No. Signal Name Address Bit No. Signal Name
0000h 0 Device No. Bit0 0002h 0 Start(R)
1 Device No. Bit1 1 Cycle Stop(R)
2 Device No. Bit2 2 Cancel(R)
3 Device Added Information Bit0 3 Alarm Off(R)
4 Device Added Information Bit1 4 Recovery(R)
5 Device Added Information Bit2 5 Servo(R)
6 Device Added Information Bit3 6 Enable(R)
7 Output Register Value Bit0 7 Setup(MXR)
0001h 0 Output Register Value Bit1 0003h 0 Setup(CFB-R)
1 Output Register Value Bit2 1 Go Front(R)
2 Output Register Value Bit3 2 Auto/Manual Select Switch (R) (1:Auto)
3 Output Register Value Bit4 3 EMG(R)
4 Input Register Value Bit0 4 Rear Cover OPEN Detection
5 Input Register Value Bit1 5 EMG Stop External Input
6 Input Register Value Bit2 6 Slowdown External Input
7 Input Register Value Bit3 7
■ Device 10
Address Bit No. Signal Name Address Bit No. Signal Name
0000h 0 Device No. Bit0 0005h 0
1 Device No. Bit1 1
2 Device No. Bit2 2
3 Device Added Information Bit0 3
4 Device Added Information Bit1 4 Air Pressure Down (failure)
5 Device Added Information Bit2 5 Ready Input
6 Device Added Information Bit3 6 Board Available Input
7 Output Register Value Bit0 7 AWC Pin Detection
0001h 0 Output Register Value Bit1 0006h 0 CFB(F) Lock
1 Output Register Value Bit2 1 CFB(F) Unlock
2 Output Register Value Bit3 2 CFB(F) Check 1
3 Output Register Value Bit4 3 CFB(F) Check 2
4 Input Register Value Bit0 4 CFB(R) Lock
5 Input Register Value Bit1 5 CFB(R) Unlock
6 Input Register Value Bit2 6 CFB(R) Check 1
7 Input Register Value Bit3 7 CFB(R) Check 2
0002h 0 Board Stopper Up A 0007h 0 ANC A Close
1 Board Stopper Down 1 ANC A Open
2 Main Clamp Up A 2 ANC B Close
3
3
ANC B Open
4 Main Clamp Down 4
5 5
6 6 MXST2 L Position 1
7 Entrance Sensor 7 MXST2 L Position 2
0003h 0 Entrance Shutter Close 0008h 0 Rear Clamp On
1 Buffer Stopper Up 1 Rear Clamp Off
2 Buffer Stopper Down 2 Side Clamp On
3 Main Conveyor Arrival A 3 Side Clamp Off
4 Exit Sensor 4
5 5
6 Entrance Buffer Arrival 6
7 Exit Buffer Arrival 7 Conveyor Width Sensor
0004h 0 000Bh 0 Conveyor1 Alarm
1 1 Conveyor2 Alarm
2 2 Conveyor3 Alarm
3 3
4 X Regenerative Resistor Thermal Alarm 4
5 Y1 Regenerative Resistor Thermal Alarm 5
6 Y2 Regenerative Resistor Thermal Alarm 6
7 7

4 Electrical Section
4-16
■ Device 12
Address Bit No. Signal Name Address Bit No. Signal Name
0000h 0 Device No. Bit0 0003h 0
MXR Pallet Bar Open1 / MX20 Pallet
Interlock in Stocker
1 Device No. Bit1 1
MXR Pallet Bar Open2 / MX20 Pallet
Stopper Off in Stocker
2 Device No. Bit2 2
MXR Pallet Bar Close1 / MX20 Pallet
Clamp Off on Shuttle
3 Device Added Information Bit0 3
MXR Pallet Detect in Stocker / MX20
Pallet Detect in Stocker
4 Device Added Information Bit1 4
MXR Hook Unlock / MX20 Relay Hook
Down
5 Device Added Information Bit2 5 W-MXR SETUP Switch
6 Device Added Information Bit3 6 MXR Cover Open / MX20 Cover Open
7 Output Register Value Bit0 7 W-MXR RELAY ON
0001h 0 Output Register Value Bit1 0004h 0 W-MXR SERVO Switch
1 Output Register Value Bit2 1 W-MXR EMG
2 Output Register Value Bit3 2 IN1
3 Output Register Value Bit4 3 IN2
4 Input Register Value Bit0 4 IN3
5 Input Register Value Bit1 5 IN4
6 Input Register Value Bit2 6 IN5
7 Input Register Value Bit3 7 IN6
0002h 0
1
2 MXR Pallet I/L
3
4 MXR Pallet Bar Close2
5 MXR Stocker I/L / MX20 Stocker I/L
6
MXR Hook Lock / MX20 Relay Hook Retract
End
7
MXR Pallet Detect on Hook / MX20 Pallet
Detect on Shuttle

4 Electrical Section
4-17
Control Board
Handling Control Board
Note the followings when handling PC boards.
Do not touch control boards by wet hands.
Do not handle control boards where there are metal chips around.
To handle control boards in the control rack, never touch the connecting portion where gold is plated. If
the connecting portion is covered with dust, the machine doesn't work properly. Clean with alcohol.
Gold Plating