00900068-02_SM_ASM_ProcessLens_EN.pdf - 第12页

ASM Proces sLens Single - l ane 03/2020 Edit ion 12 1.3.4.2 Important Measur es to Protect Against Static Charging ► Most plas tics can easil y becom e charged and m us t theref ore be k ept awa y from at - risk componen…

100%1 / 92
ASM ProcessLens Single-lane 03/2020 Edition
11
1.3 Other Instructions
1.3.1 Environmentally-Friendly Disposal of Materials and Components
SIPLACE products are manufactured using only materials and parts that can be easily separated
and disposed of in an environmentally-friendly way.
The company operating the system has sole responsibility for the proper,
environmentally-
parts.
► Please observe your national statutory provisions for waste disposal and
1.3.2 Use of Original SIPLACE Accessories and Spare Parts
Only use original spare parts and authorized accessories. The use of other parts will affect safety
and will invalidate the liability for any consequential damage.
1.3.3 Information about This Service Manual
WARNING
The service work described in this manual may only be performed by specially trained
1.3.4 ESD Guidelines
1.3.4.1 Definition of ESD
Almost all of the modules in use today are equipped with highly integrated MOS blocks and
components. The manufacturing techniques used mean that these electronic components are
extremely sensitive to overvoltage and thus to electrostatic discharge.
The abbreviation for such modules is "ESD"(Electrostatic Sensitive Device).
This is used internationally, although the German abbreviation "EGB" may
also be seen. The following symbol on cabinet rating plates, racks or
packaging indicates that components which are sensitive to electrostatic
discharge have been used and thus that the modules concerned are also
touch-sensitive
ESDs can be destroyed by voltages and power levels that are far below the level that can be
perceived by humans. Such voltages occur if a person touches a component or module without
earthing themselves. Components that are exposed to such overvoltages do not generally appear
to be defective immediately - incorrect behavior starts after the component or module has been in
operation for some time.
ASM ProcessLens Single-lane 03/2020 Edition
12
1.3.4.2 Important Measures to Protect Against Static Charging
► Most plastics can easily become charged and must therefore be kept away from at-risk
components.
► Always ensure that people, the workplace and packaging are safely earthed when handling
electrostatic sensitive components.
1.3.4.3 Handling ESD Modules
Do not touch electronic modules unless it is absolutely essential to do so in order to carry out other
work. If it is necessary, make sure that you do not touch the pins or printed conductors when you
pick up flat modules.
Do not touch components unless
● You are constantly earthed by an ESD wrist strap or
● You are wearing ESD shoes or ESD shoe earthing strips on an ESD floor.
Always discharge yourself before you touch an electronic module. To do this, simply touch a
conductive and earthed object immediately before you touch the module (such as unpainted parts
of a switch cabinet, a water pipe, etc.).
Do not allow modules with chargeable and highly insulating materials to touch one another, e.g.
plastic films, insulating table surfaces or items of clothing made from synthetic fibers.
Always place the modules on a conductive surface (table with an ESD coating, conductive ESD
foam, ESD bag or container).
Do not bring modules near visual display units, monitors or televisions. Keep them at least 10 cm
away from the screen.
1.3.4.4 Measurements and Modifications to ESD Modules
Measurements of the assemblies may only be taken if
● The measuring device has been grounded (e.g. via protective conductor) or
● The measuring head of the potential-free measuring device has been briefly discharged before
measurement (e.g. touching blank metal control unit housing).
► Always use an earthed soldering iron if you carry out any soldering work.
1.3.4.5 Dispatching ESD Modules
► Always store modules and components in conductive packaging (e.g. metallized plastic bags or
metal sleeves) and dispatch them in conductive packaging.
► If the packaging is not conductive, place the modules in a conductive envelope before
packaging. Use conductive foam rubber, ESD bags, domestic aluminum foil or paper, for
example. NEVER use plastic bags or film.
► If the module has integral batteries, ensure that the conductive packaging does not touch or
short-circuit the battery terminals and, if necessary, first cover the terminals with insulating tape
or material.
1.3.5 Validity of Document
This document contains service work instructions for the ASM ProcessLens machine.
The manual focuses on describing mechanical service work.
Please refer to the circuit diagram folder for any electrical checks.
ASM ProcessLens Single-lane 03/2020 Edition
13
1.3.6 Release History
Document
ASM ProcessLens Single-lane
Service manual
Edition Changes
03/2020 New chapter “4 Machine - Calibrations”
1.3.7 SIPLACE on the World Wide Web (WWW)
Log into our SIPLACE
®
homepage at http://www.asm-smt.com.
The different sections contain information about our products, services and contact persons.
In addition, registered customers can also access the SIPLACE User Group. Here you can call up
special information about our solder paste inspection systems e.g.
● Technical documentation,
● Technical information,
● Spare parts lists etc.
1.4 Staff Qualifications and Training
Qualified or adequately trained personnel means that these people are familiar with the setting up,
operation and maintenance of automatic solder paste inspection systems and add-on devices and
are suitably qualified, e.g.:
● Have been trained, instructed or authorized to switch on and off, isolate, earth and identify
electrical circuits and system components in accordance with normal safety standards.
● Have been trained or instructed in the upkeep and use of appropriate safety equipment in
accordance with normal safety standards.
● Have received first aid training.