00192402-01.pdf - 第222页

GEM for SIPLACE V7.01 Page 222 of 251 ©Siemens AG, all rights r eserved CEID Name Descri ption 811037 FM_W P_CHECKSUMME c hecks um error* 1 811038 FM_W PW error* 1 811039 FM_W P_NULLKORR dis tance between zero point of W…

100%1 / 251
GEM for SIPLACE V7.01
©Siemens AG, all rights reserved page 221 of 251
CEID Name Description
811009 FM_WP_RAHMEN WPC: No tray available* 1
811010 FM_WP_RUESTUNG_Q WPC: Sent set-up contains errors* 1
811011 FM_WP_SPEICHER WPC: Data loss in component table
(defective battery) *
1
811012 FM_WP_TIMEOUT_T WPC: Fault in feed axis (Servo or
axis card) *
1
811013 FM_WP_ENDSCH_T WPC: Feed axis at limit switch* 1
811014 FM_WP_ACHSE_T WPC: Axis error of feed axis* 1
811015 FM_WP_SCHALTER_T WPC: Feed axis servo released* 1
811016 FM_WP_ZANGE WPC: Error in jaw position* 1
811017 FM_WP_TIMEOUT_P WPC: Fault in lifting axis (Servo or
axis card) *
1
811018 FM_WP_ENDSCH_P WPC: Lifting axis at limit switch* 1
811019 FM_WP_ACHSE_P WPC: Axis error of lifting axis* 1
811020 FM_WP_SCHALTER_P WPC: Lifting axis servo released* 1
811021 FM_WP_STEUERUNG WPC: Control switched off* 1
811022 FM_WP_SCHUTZ WPC: Protection at component table
open*
1
811023 FM_WP_TRANSP WPC: Error while transporting tray* 1
811024 FM_WP_RUESTUNG WPC: Error in saved set-up* 1
811025 FM_WP_FEHLT WPC: One tray of saved set-up
missing*
1
811026 FM_WP_MAGAZIN WPC: When returning tray, level
occupied*
1
811027 FM_WP_VERSCHW WPC: Tray has been taken out* 1
811028 FM_WP_UEBERG WPC: Take-over position already
occupied*
1
811029 FM_WP_VERDREHT WPC: Tray in incorrect pos. or
protection not closed properly*
1
811030 FM_WP_SICHERUNG WPC: Feed axis has touched
protection*
1
811031 FM_WPW_NFPOS WPC must be moved from refill
position*
1
811032 FM_WP_WRITE_HD Error while writing WPC machine data
to hard disk*
1
811033 FM_WP_READ_HD Error while reading WPC machine
data from hard disk*
1
811034 FM_WP_WRITE_FD Error while writing WPC machine data
to floppy*
1
811035 FM_WP_READ_FD Error while reading WPC machine
data from floppy*
1
811036 FM_WP_ANSCHLAG limit switch not found* 1
GEM for SIPLACE V7.01
Page 222 of 251 ©Siemens AG, all rights reserved
CEID Name Description
811037 FM_WP_CHECKSUMME checksum error* 1
811038 FM_WPW error* 1
811039 FM_WP_NULLKORR distance between zero point of WPC
axis and reference BERO to small*
1
811040 FM_WP_80F3_MA error reading standard machine data
for WPC*
1
* Depending on the collection event, some of the status variables <ERRORTYPE>,
<GANTRYONERROR>, <SEGMENTONERROR>, <TRACKONERROR>,
<ERRORINFO1> and <ERRORINFO2> will be updated at each of these waffle pack
changer collection events.
%DUFRGH
CEID Name Description
RPT
920001 BCread The barcode reader transmits a
barcode <BCININPUTCONVEYOR>
24
920002 ComponentBCread A component barcode is read via the
GUI.
27
920011 BCTwinRead The barcode reader transmits a
barcode
<BCINTWININPUTCONVEYOR> from
the twin conveyor.
30
921001 FM_LP_BC_NOK PCB barcode: incorrect format* 1
921002 FM_LP_BC_KEINE_DAT No data received from PCB barcode
reader*
1
921003 FM_BC_ZU_LANG Barcode too long, cut off! * 1
921004 FM_BL_INPUT_NOK BL: unexpected input* 1
921005 FM_LP_KEIN_BC No PCB barcode read* 1
921006 FM_GK_LR_DURCHTRANSP Caution: PCB transported through by
line computer*
1
* Depending on the collection event, some of the status variables <ERRORTYPE>,
<GANTRYONERROR>, <SEGMENTONERROR>, <TRACKONERROR>,
<ERRORINFO1> and <ERRORINFO2> will be updated at each of these barcode
collection events.
*(0.HUQHO
&(,' 1DPH 'HVFULSWLRQ
1000001 EqConstChange Equipment constant changed at the
machine
0
1000002 S10Ack 1
Communication Model
Control State Model
1000003 GemControlStateLOCAL SIPLACE goes to local mode 0
GEM for SIPLACE V7.01
©Siemens AG, all rights reserved page 223 of 251
&(,' 1DPH 'HVFULSWLRQ
1000004 GemControlStateREMOTE SIPLCAE goes to remote mode 0
1000005 GemEquipmentOFFLINE SIPLACE goes OFFLINE 0
1000006 GemControlStateOFFLINE Control state goes to OFFLINE 0
1000018 ControlModeChanged <CONTROLMODE> state changed
(LCU, GEM-Host, Stand-alone)
0
1000019 OperatorCommand The operator issued a „host -
available“ command while the
SIPLACE is in Remote mode.
1
Spooling
1000007 GemSpoolingActivated Spooling is activated. This event is
never reported directly to the host,
but instead is directed as the first
message to the spool file
0
1000008 GemSpoolingDeactivated The spool area has been completely
emptied.
0
1000009 GemSpoolTransmitFailure Communication error during
transmitting spooled messages to
host. This event is never reported
directly to the host, but instead it is
directed to the end of the spool file
0
Process State Model
1000010 Init2Process The Siplace change its processing
state from „Machine Initialization“ to
„Processing“
1
1000011 Process2Init The Siplace change its processing
state from „Processing“ to „Machine
Initialization“
1
1000012 Process2SingleFunction The Siplace change its processing
state from „Processing“ to „Single
Function“
1
1000013 SingleFunction2Process The Siplace change its processing
state from „Single Function“ to
„Processing“
1
1000014 Init2SingleFunction The Siplace change its processing
state from „Machine Initialization“ to
„Single Function“
1
1000015 SingleFunction2Init The Siplace change its processing
state from „Single Function“ to
„Machine Initialization“
1
Process Program Management
1000016 GemPPChangeEvent Program changed at the machine 1
1000017 GemBadDownloadEvent Error in downloaded program 1
1001018 FM_GEM_INIT GEM: Error upon initialization of
GEM interface to host*
1
1001019 FM_GEM_INIT_MC GEM: Error upon initialization of
interface to MC*
1