00194547-09_InstallationManual_60103SP4_EN_DE.pdf - 第51页
Installation Manual, Station Software Version 601.03 SP4 Edition 05/2007 Menu item Comment Selection options Suspend Mode The time is set here before the system switches to suspend mode. Disabled ; 1 Min; 2 Min; 4 Min; 8…
Installation Manual, Station Software Version 601.03 SP4 Edition 05/2007
4.5.1.11 Setup page "Power Management Setup"
Menu item Comment Selection options
ACPI Support
ACPI version 1.0 is implemented in the BIOS. Statuses S1
and S3 are supported by the hardware of the
CPCI-/SMP16-
CPU076.
Enabled, ACPI is only supported automatically as of Win98.
When installing Win95, ACPI installation must be initiated by
hand.
Disabled means that ACPI is also not supported for an
ACPI-compatible operating system.
Enabled
Disabled
ACPI Suspend Type
Specifies the status in which the computer shuts down in
Suspend Mode using ACPI.
S1 (POS)
S3 (STR)
Power Management
This field is the main switch for the power saving modes.
There are three settings:
Max Saving Switches the computer to
power saving mode after a brief
time of inactivity.
Min Saving Works almost exactly in the same
way as Max Saving, but the inactivity time
required for switching is longer.
User Defined Enables the power saving mode options to
be set individually.
User Define
Min Saving
Max Saving
Video Off Method
This sets the way in which the monitor is switched to power
saving mode. There are three options available:
DPMS (Display Power Management)
enables the BIOS to control
DPMS-capable graphics cards.
Blank Screen Darkens the screen and
should be used with monitors
without Power Management
functions.
V/H Sync+Blank darkens the screen by switching
vertical and horizontal
scanning.
Blank Screen
V/H Sync+Blank
DPMS
Video Off In
Suspend
Specifies whether the monitor interface is switched off in
suspend mode (no sync signals)
No
Yes
MODEM Use IRQ
This option determines which IRQ registers the ring tone of
the modem for faxing.
NA; 3; 4; 5; 7;9; 10; 11
50 of 89
Installation Manual, Station Software Version 601.03 SP4 Edition 05/2007
Menu item Comment Selection options
Suspend Mode
The time is set here before the system switches to suspend
mode.
Disabled;
1 Min; 2 Min;
4 Min; 8 Min;
12 Min; 20 Min;
30 Min; 40 Min;
1 Hour
HDD Power Down
The time is set here after which the hard disk is switched to
Power Down mode
Disabled;
1 Min; 2 Min;
3 Min; 4 Min;
5 Min; 6 Min;
7 Min; 8 Min;
9 Min; 10 Min;
11 Min; 12 Min;
13 Min; 14 Min;
15 Min
USB KB Wake-Up
From S3
If disabled is set, the system cannot by woken up from the
S3 state (Suspend to RAM) by a USB keyboard.
Enabled
Disabled
CPU Thermal-
Throttling
If the system begins to throttle due to a thermal overload,
this is the ratio in percent: switch-off time / (switch-off time +
on time). This value is factory set and cannot be changed.
87,5%
Resume by Alarm
If this option is switched on, the computer is retrieved from
power saving mode at the specified date and time. If 0 is
specified as a date, this is done on a daily basis.
Enabled
Disabled
Date (of Month)
Alarm
all values between 0 and
31
0
Time (hh:mm:ss)
Alarm
valid time
0:0:0
Reload Global
Timer Events
Every event of a device listed below resets the global
counter for suspend mode, if this is enabled.
Enabled
Disabled
51 of 89
Installation Manual, Station Software Version 601.03 SP4 Edition 05/2007
4.5.1.12 Setup page "PNP/PCI Configuration"
Menu item Comment Selection options
PNP OS Installed
Yes, if the operating system used is plug and play-
compatible (e.g. Win9x); No, if it is not
No
Yes
Reset Configuration
Data
Enabled instructs the PNP BIOS to reset all devices and
assignments.
Enabled
Disabled
Resources
Controlled By
The Manual setting can be used to reserve the interrupts
and DMA, otherwise they will automatically be assigned by
the BIOS (PnP Extension).
If no PNP operating system has been installed, use Auto.
Auto (ESCD)
Manual
IRQ Resources
This field is only enabled if the option Manual is enabled
under Resources Controlled By. Pressing the Enter key
will display a submenu in which the interrupts can be
released for assignment by the PNP BIOS (setting PCI/ISA
PnP) or not assigned by the PNP BIOS (setting Legacy
ISA)
PCI/ISA PnP
Legacy ISA
DMA Resources
This field is only enabled if the option Manual is enabled
under Resources Controlled By. Pressing the Enter key
will display a submenu in which the DMA channels to be
assigned by the PNP BIOS are disabled (setting PCI/ISA
PnP) or not assigned by the PNP BIOS (setting Legacy
ISA)
PCI/ISA PnP
Legacy ISA
PCI/VGA Palette
Snoop
Color reproduction may be corrupted with some graphics
adapters such as graphics accelerators or MPEG adapters
which do not conform to the VGA standard. In this case,
set Enabled
Enabled
Disabled
Assign IRQ for USB
Enabled assigns a PCI IRQ to the USB controller.
Enabled
Disabled
PCI INT A Assignment
PCI INT B Assignment
PCI INT C Assignment
PCI INT D Assignment
PCI INT E Assignment
PCI INT F Assignment
PCI INT G Assignment
PCI INT H Assignment
With this setting, the BIOS can be instructed to assign a
defined IRQ to a PCI interrupt. A prerequisite for this is that
this IRQ is not set to Legacy ISA. When Auto is set, the
BIOS automatically assigns the IRQ.
Auto; 3; 4; 5; 7; 9; 10;
11; 12; 14; 15
52 of 89