00198705-01_AI_Portalmodularität_SX12_V3_DE_EN.pdf - 第98页

3 Fitting the Gantry 3.3 Gantry Preparations 98 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 Locking the gantry carrier correctly Fig.23: Engaging the gantry ca…

3 Fitting the Gantry

3.3 Gantry Preparations

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 97

Move the gantry lift into position

Fig.20: Gantry lift in position

► Carefully move the gantry lift (1) up to

the gantry.

 CAUTION!

Take care not to damage the gantry

when moving it with the gantry lift.

Do not hit the gantry or locks with the

gantry carrier plate(3).

Make sure that the gantry carrier plate

(3) protrudes above the gantry carrier

locks(4).

► Remove the foam cover (2).

3.3.3 Locking and Transporting the Gantry Carrier

Move the gantry lift to the gantry

Fig.21: Lowering the gantry carrier

► Move the gantry carrier plate (2) for the

gantry lift over the gantry carrier locks

(3). The groove (1) must be able to en-

gage with the two locking plates (3).

► Lower the gantry lift so that the gantry

carrier plate can slide into the locks (4).

► Move the lift only so far down that the

locking lever (5) can be closed.

Locking the gantry carrier

Fig.22: Locking the gantry carrier

► Press the lock (4) back and pull (1) the

handle (2) of the lock upwards.

ð The lever (3) will engage. The

spring on the lock (4) secures the

locking mechanism.

3 Fitting the Gantry

3.3 Gantry Preparations

98 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020

Locking the gantry carrier correctly

Fig.23: Engaging the gantry carrier

► Check that the lever (2) on the lock (1)

has engaged properly.

► To open, press the lock backwards and

then press the lever downwards. This

opens the lock.

Securing the gantry in the transportation crate

Fig.24: Gantry secured

► The gantry is fixed with 4 screws (1) in

the transportation crate. Loosen these

screws.

 CAUTION!

Only transport the gantry with the

gantry lift when the arms are locked!

► Move the gantry lift upwards and care-

fully lift the gantry out of the transporta-

tion crate.

 NOTICE!

The placement head must be in the

center of the gantry.

This ensures that the load is distrib-

uted evenly during transportation.

3 Fitting the Gantry

3.3 Gantry Preparations

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 99

3.3.4 Transportation Locks and Tilt Guard

Fig.25: Transportation locks

The gantry is locked with three transporta-

tion locks (1) and (3) at the gantry carrier. In

addition, the head plate has two transporta-

tion locks (2) for the placement head.

CAUTION

Docking

► Flap down the transportation lock plates right before the docking.

► Make sure that the gantry does not slide off the gantry carrier during rerailing respec-

tively derailing and that the tilt guard is suspended in order to hold the gantry in posi-

tion.

► Move the green lever upwards and swivel the transportation lock to one side.

► There is another lever at (3). Move the green lever upwards and remove it.

► Loosen the two screws fastening the transportation locks (2) to the head plate in each case

and remove both locks.

NOTICE

Storing the transportation locks

If the gantry is transported or packed back into the transportation crate, you need to refit the

transportation locks.

► Place the transportation locks in the crate for later usage.