00198610-01_VD_712.0_R18-2_DE_EN.pdf - 第35页

Station Software 71 2.0 (R18 - 2) / Versio n Description 11/2018 Edition 35 D1 - 153552201 There was a problem w hen synchronizing S MEMA and whisperin g data between adjacent m achines. D1 - 153630802 Error m essage 304…

Station Software 712.0 (R18-2) / Version Description 11/2018 Edition

711.1 SP1

Error no. Error description

D1-140512109 Automatic program download via barcode: machine needed to be emptied

when using smart pins although the pins were in the same position in both

programs.

D1-144918301 The binder of the linear feeder did not open at the first pickup event.

D1-145486749 eSW: conveyor error messages 30007 Cannot open file and 35336 An

unknown conveyor control unit has been detected after machine

start.

D1-149326501 During production, there was a message that the "Application has to be

closed.

D1-150606549 In case of contactless pickup, the z height was not re-taught, and the feeder

pocket was not measured again after a foil torn.

D1-150924808 Improvement of the manual Pin 1 check to be able to recognize low-contrast

structures.

D1-151189122 eSW: Vacuum for vacuum tooling was not turned on automatically during

recovery placement mode.

D1-151304001

D1-151342257

D1-152045605

After having continued the mapping after a Vision error the mapping

component was lost, and the mapping could not be finished.

D1-151804201 In the Feeder Parameter view, the information "spacer is needed" was

displayed for components with contactless pick-up although current feeders

did no longer need a spacer.

D1-152045605 It was not possible to teach a pickup offset of more than 1 mm for a WPC tray.

D1-152513701 Picking up from 2 special feeders with undefined busy time led to performance

loss as the feeders did not answer quick enough.

D1-152745201

D1-153297807

D1-153360401

D1-154070049

Sporadic problems during the benchmark placement (SX2 with TH).

D1-152748201 Virtual PCB stack: a multi panel board could not be placed.

D1-152854543 After having moved to the nozzle changer position on location 2 in the teach

menu, the software stopped, and the machine had to be switched off.

D1-153217601 37800 [Twin Head, gantry 1] Machine stopped due to too many

repetitive errors.

D1-153325901 PPW 1_L could not be calibrated.

D1-153333101 TX2 V2 with CPP/C&P20 P2 (nozzle changer for CPP is 3.65 mm lower):

there was a warning during calibration of the nozzle changer that the 3 mm

border was exceeded.

D1-153360489 The virtual keyboard was in the background of the input window of the bug

reporter.

D1-153368126 Error message 32507 Product change: Finishing previous

product prior to setup change and no more boards got into the

machine.

D1-153466646 When adjusting the pickup offset, the gantry was moving 300 mm towards the

conveyor instead of going to the pickup position of the WPC.

Station Software 712.0 (R18-2) / Version Description 11/2018 Edition

D1-153552201 There was a problem when synchronizing SMEMA and whispering data

between adjacent machines.

D1-153630802 Error message 30450 Unspecified hardware error was displayed for

each camera but there was no problem at the machine.

D1-153875301 eSW: there was a problem with the transition between the SIPLACE and

AYSY conveyors.

D1-153989601 Changing the conveyor width led to error message Unexpected software

malfunction - the application has to be closed

D1-154055101 The firmware update for the C&P20 pressure regulator could not be done.

D1-154075385 After having downloaded the conveyor BIOS, the subsystem could not be

activated.

D1-154379501 The service symbol was not active after the machine started.

D1-154598802 In stand-alone mode, old jobs could not be deleted any longer.

D1-154781809 Threshold = 0 had no effect: the machine stopped although no threshold was

defined within Setup Center.

D1-155170101 The fiducial plate position of the SST47 could not be calibrated.

D1-155177302 The machine reported a yellow board with an unknown placement state, but

this position could not be checked within the manual operations because just a

grey field was displayed.

D1-155243901 The calibration of the offset between SST47 and SST34 failed.

D1-155371401 Sporadically, the station software stopped during placement with error

message

32602 The software has stopped unexpectedly

D18199-16132 Better handling within the station software for the selection of component

shapes that shall be taught.

D18272-5888 eSW: A 440 mm board did not reach the placement area in an X4 S

placement machine with short input conveyor.

D18445-3801 Sporadically, the station software stopped during placement with error

message

32602 The software has stopped unexpectedly

D18459-1601 The machine displayed an X-axis error 30341: Position is out of

range

D18474-3601 Special FFI feeder brought error message 40007 out of components

although feeder was filled up with 1200 components.

D18505-3253 Sometimes component teaching slowed down the computer.

D18541-2515 Chuck fiducials CA4: If the vacuum tooling fiducials were not used for

recalibration, a dual gantry measurement must be done.

D18570-1501 The machine stopped during placement without error message.

D18585-2817 Moving a gantry to service position did not work and the error message

32535

Checking nozzle configuration: CPP Head, gantry1 was

displayed.

Table 8-3: Corrected errors station software version 711.1 SP1

Station Software 712.0 (R18-2) / Version Description 11/2018 Edition

711.1 Patch 2

Error no. Error description

D1-147902801

D1-151728101

eSW: the machine stopped during dry run with cyclic transport with the error

message

unknown placement state

D1-150565001

D1-153597901

D1-150820801

D1-153597901

After an eSW download we always got the information that heads had been

changed.

D1-150590901 Sporadically, the station software stopped during placement with the error

message

30016 Unhandled exception error

D1-153569301 For an alternative component shape, the dimensions of the original shape

were used. Thus, this function could not be used if the alternative shape had

different dimensions.

D1-153862701 Teaching of the component position did not always work.

D1-154709901

D1-154855101

The conveyor fiducials were checked after every board.

D18460-15207 Machine picked up 2 large components with the TH. The components

collided when being rotated.

D18537-2101 When a barcode was whispered to the next machine, a tabulator was

replaced by a space character.

Table 8-4: Corrected errors station software version 711.1 Patch 2

711.1 Patch 1

Error no. Error description

D1-127453301 E by SIPLACE, eSW: the feeders were in an undefined state after a restart of

the machine.

D1-151650901 The height for the CPP head within a TX2 V2 machine was wrong when the

CPP head was mounted in a low position.

D1-152039901 The WPC was not displayed correctly in the main view of the GUI.

D18581-2801 The machine stopped after 80 vision errors, although the repick count was set

to 100.

Table 8-5: Corrected errors station software version 711.1 Patch 1