00192792-02.pdf - 第55页
SIPLACE 80 S-25 HM 2 Retrofitting Instructions: Matrix Tray Changer MTC on S-25 HM (Option) 01/01 Issue 2.4 Safety Instructions 55 6DIHW\ ,QVWUXFWLRQV DANGER The Safety instruc tions in c hapter " Operationa l …
2 Retrofitting Instructions: Matrix Tray Changer MTC on S-25 HM (Option) SIPLACE 80 S-25 HM
2.3 Required time 01/01 Issue
54
– Mount track scale (starting at track 67) on the new empty-tape duct.
– Remove LH safety doors -> Modify RH safety door.
– Adjust height of MTC -> Carefully move MTC in for the first time.
– Align MTC by means of an adjustment gauge (fisheye), to be inserted into conveyor area 2.
– Assemble the machine, installing the new component reject box (MTC/component table) in the
process.
– Configure and measure nozzle changer -> Measure MTC; set up nozzle changer and MTC.
5HTXLUHGWLPH
- Installation of "110V~ voltage module MTC" (option)approx. 1 hour
- Installation of MTC and appropriate nozzle changerapprox. 1 hour
- If necessary: adjust height of MTC approx. 1 hour
- Configure an calibrate approx. 1.5 hours
SIPLACE 80 S-25 HM 2 Retrofitting Instructions: Matrix Tray Changer MTC on S-25 HM (Option)
01/01 Issue 2.4 Safety Instructions
55
6DIHW\ ,QVWUXFWLRQV
DANGER
The Safety instructions in chapter "Operational Safety" in the User Manual SIPLACE S-25 HM
take precedence.
Improperly handling the MTC fosters a risk of serious injury.
In addition take note of ALL "Safety instructions" in the "User Manual MTC" (Item no.
00192317-01).
The machines SIPLACE S-25 HM are powered by
120V / 208V +/- 5% (US version) or 3 x 230V/400V +/-5%, 50/ 60 Hz line voltage.
Portions of the system are therefore conducting dangerous electricity, inside the machine and in-
side the MTC, even while the master switch is turned off.
After you have properly carried out the shut-down of the Windows operating system NT:
BEFORE all work of retrofitting the machine must be turned OFF at the main switch and isolated
from the mains.
In addition, the compressed air supply must be turned off at the main valve of the compressed air
unit in the machine base and the compressed air lines must be bled by actuating the needle valve
at the compressed air unit (particularly due to the risk of injury - posed by residual air - at the pneu-
matic cutter after undocking/removing the component changeover table).
Obey the applicable accident prevention regulations, DIN standards and special safety codes of
your country at all times. DIN EN 60204 must be adhered to during all work inside the machine
base.
Follow the instructions regarding residual voltages in Chapter "Operational Safety".
Comply with regulations on ESDs (see Chapter "Operational Safety")
While retrofitting you are working in the gantry positioning range.
During the whole process secure the machine conscientiously against other personnel and pre-
vent it from being turned back on without authorization, as described in the User Manual in the
chapter "Locking the Machine...".
In additional, there is a higher risk of accident when working with the SITEST program.
The SITEST program is only to be started by personnel who are authorized to do so.
For the work with the SITEST program the component changeover table and the MTC (incl. com-
ponent table) must be moved in and correctly connected.
2 Retrofitting Instructions: Matrix Tray Changer MTC on S-25 HM (Option) SIPLACE 80 S-25 HM
2.4 Safety Instructions 01/01 Issue
56
'HILQLWLRQV
DANGER
in terms of these instructions means that death, severe bodily injury or considerable material dam-
age WILL occur if the instructions about danger are not followed.
WARNING
in terms of these instructions means that death, severe bodily injury or considerable material dam-
age may occur if the warnings are not heeded.
CAUTION
in terms of these instructions mean that minor bodily injury or material may occur if the cautions
are not heeded.
NOTE
in terms of these instructions is a statement of important information about the product or the
pertinent portion of the instructions to which particular attention is being drawn.