MPM全自动印刷机中文操作手册.pdf - 第22页
22 Now , adjust the vacuum rear and ( 現在請調整後隔板和側 ( 左右 ) 隔板 ) side plates If you have a dedicated work holder , ( 若有使用專用 PCB 板支撐架 , 請現在 install it now 把他裝上 ) Pr ess NEXT to Continue, or EXIT to Quit. ( 按 NEXT 繼續 , 按 EXIT …
21
Press Done when finished. (當你做完上述之步驟，按 Done)
Stencil Dimensions
鋼板尺寸設定參數
Inner 660.400
鋼板尺寸
Enter stencil inner dimension(輸入內部鋼板尺寸)
Press Done when finished. (當你做完上述之步驟，按 Done)
1.2 選擇 Worknest 進入印刷工作平台參數設定
Hardware Required:
Board ,Tactile , Vacuum Chucks
Please remove the stencil. (請移開鋼板)
Squeegee will now move back. (刮刀組現在將移動到後面)
Press SELECT when ready. (準備好後按 SELECT)
按 NEXT 之後，出現下列訊息：
Worknest
Enter stencil inner dimension
Press Done when finished.
Please remove the stencil.
Squeegee will now move back.
Press SELECT when ready.
Now, adjust the vacuum rear and side plates
If you have a dedicated work holder, install it now
Press NEXT to Continue, or EXIT to Quit.
22
Now, adjust the vacuum rear and (現在請調整後隔板和側(左右)隔板)
side plates
If you have a dedicated work holder, (若有使用專用 PCB 板支撐架,請現在
install it now 把他裝上)
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
按 NEXT 之後，出現下列訊息：
The Z TOWER is about to load (Z 軸上升到 tooling height 的位置)
to tooling height
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
你按 NEXT 之後，出現下列訊息：
If you have X snuggers,adjust snugger pins now. (若有使用 X 方向夾板,請
調整好)
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
你按 NEXT 之後，出現下列訊息：
The Z TOWER is about to load
to tooling height
Press NEXT to Continue, or EXIT to Quit.
If you have X snuggers,adjust snugger pins now.
Press NEXT to Continue, or EXIT to Quit.
23
CAUTION, The machine is now going to(注意,機器現在將移動到基板
Center itself for this size board. 中心點)
The Y AXIS is about to move forward. (Y 軸即將移動到前面(基板中心點)
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
Board Parameters
基板(PCB)參數設定
Detent 12.7
PCB 停於中心印刷位置值
Load speed 432
進板軌道皮帶轉速值(數字越大,轉速越快)
Unload speed 381
出板軌道皮帶轉速值(數字越大,轉速越快)
Enter board loading parameters. (輸入 PCB 進板參數)
Click on detent field to test. (點取 detent,測試 PCB 停於中心印刷位置值)
Press Done when finished. (按 Done 完成全部動作)
CAUTION, The machine is now going to
Center itself for this size board.
The Y AXIS is about to move forward.
Press NEXT to Continue, or EXIT to Quit.
Enter board loading parameters.
Click on detent field to test.
Press Done when finished.