00197288-02_AI_TBO_SX12_V2_DE_EN.pdf - 第40页

1 Introduction 1.3 Other instructions 40 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V2 Thick Board Option Option Dicke Leiterplatte 02/2019 1.3.3.2 Important measures to protect against static charging ► Mo…

1 Introduction

1.3 Other instructions

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V2 Thick Board Option Option Dicke Leiterplatte

02/2019

Testing

Service personnel may test circuits by energizing them briefly without suspending the Lock Out /

Tag Out Procedure. This may only be done when no other work is being performed by any other

person on the equipment being tested.

It is extremely important that all remote START switches are tagged with the "Do Not Operate" tag

to prevent inadvertent operation of the equipment during these periods.

Responsibilities

●

It shall be the responsibility of the maintenance and service personnel to make sure this pro-

cedure is adhered to.

●

It shall be the responsibility of the maintenance and service personnel's immediate supervisor

to instruct their personnel on this procedure.

●

It shall be the responsibility of the Safety Officer to administer the Lock Out / Tag Out Proced-

ure.

1.3 Other instructions

1.3.1 Environmentally-friendly disposal of materials and components

Our products are manufactured using only materials and parts that can be easily separated and

disposed of in an environmentally-friendly way.

NOTICE

Observe the applicable regulations

The company operating the system has sole responsibility for the proper, environmentally-

friendly disposal of machines, working materials, consumable materials and wear parts.

► Please observe your national statutory provisions for waste disposal and environ-

mental protection.

1.3.2 Use of original accessories and spare parts

Only use original spare parts and authorized accessories. The use of other parts will affect safety

and will invalidate the liability for any consequential damage.

1.3.3 ESD guidelines

1.3.3.1 What does ESD mean?

Fig.4: ESD label

Almost all of the modules in use today are equipped with highly integ-

rated Metal-Oxide-Semiconductor (MOS) blocks and components.

The manufacturing techniques used mean that these electronic com-

ponents are extremely sensitive to overvoltage and thus to electro-

static discharge.

The abbreviation for such modules is "ESD" (Electrostatic Sensitive

Device). "ESD" is used internationally. The following symbol on cab-

inet rating plates, racks or packaging indicates that components

which are sensitive to electrostatic discharge have been used and

thus that the modules concerned are also touch-sensitive.

ESDs can be destroyed by voltages and power levels that are far below the level that can be per-

ceived by humans. Such voltages occur if a person touches a component or module without

earthing themselves. Components that are exposed to such overvoltages do not generally appear

to be defective immediately - incorrect behavior starts after the component or module has been in

operation for some time.

1 Introduction

1.3 Other instructions

40 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V2 Thick Board Option Option Dicke Leiterplatte

02/2019

1.3.3.2 Important measures to protect against static charging

► Most plastics can easily become charged and must therefore be kept away from at-risk com-

ponents.

► Always ensure that people, the workplace and packaging are safely earthed when handling

electrostatic sensitive components.

1.3.3.3 Handling ESD modules

As a general rule: Only touch electronic modules if you must carry out work on the modules. In that

case, make sure that you do not touch the pins or printed conductors when you pick up flat mod-

ules.

Only touch components if you are earthed by one of the following measures:

●

You are wearing an ESD wristband.

●

You are wearing ESD shoes.

●

You are wearing ESD shoe earthing strips on an ESD floor.

Immediately before you touch an electronic module, discharge your own body by touching a con-

ductive and earthed object (such as unpainted parts of a switch cabinet, a water pipe, etc.).

Do not allow modules with chargeable and highly insulating materials to touch one another, e.g.

plastic films, insulating table surfaces or items of clothing made from synthetic fibers.

Always place the modules on a conductive surface (table with an ESD coating, conductive ESD

foam, ESD bag or container).

Do not move the assemblies near to data view devices, monitors or television units. Keep a min-

imum distance of 10 cm to monitors.

1.3.3.4 Measurements and modifications to ESD modules

Only perform measurements on modules if one of the following conditions is fulfilled:

●

You are using an earthed measuring device (e.g. via PE conductors)

●

You are using a potential-free measuring device and discharge the measuring head before

the measurement (e.g.by touching an unpainted metal part of the controller casing).

► Always use an earthed soldering iron if you carry out any soldering work.

1.3.3.5 Dispatching ESD modules

► Always store modules and components in conductive packaging (e.g. metallized plastic bags

or metal sleeves) and dispatch them in conductive packaging

► If the packaging is not conductive, place the modules in a conductive envelope before pack-

aging. Use conductive expanded rubber, ESD bags, domestic aluminum foil or paper, for

example. NEVER use plastic bags or film.

► If the module has integral batteries, ensure that the conductive packaging does not touch or

short circuit the battery terminals and, if necessary, first cover the terminals with insulating

tape or material.

1.3.4 Release History

Document

SIPLACE SX1/SX2 V2

Thick Board option

Assembly Instructions

Edition Amendments

11/2012

●

Initial release

02/2019

●

New height adjustment system of the conveyor (U hooks)

1 Introduction

1.4 Staff qualifications and training

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V2 Thick Board Option Option Dicke Leiterplatte

02/2019

1.4 Staff qualifications and training

Qualified or adequately trained personnel means that these people are familiar with the setting up,

operation and maintenance of the machine and the add-on devices and are suitably qualified, e.g.:

●

Have been trained, instructed or authorized to switch on and off, isolate, earth and identify

electrical circuits and system components in accordance with normal safety standards.

●

Have been trained or instructed in the upkeep and use of appropriate safety equipment in

accordance with normal safety standards.

●

Have received first aid training.

1.5 Abbreviations

Abbreviation Description

COT Changeover table

DC Dual conveyor with 2 lanes

ESD Electrostatic sensitive device

EMC Electromagnetic compatibility

PA Placement area

PCB

Printed circuit board

Single conveyor with 1 lane