00900160-01_UM_ASM-ProcessLensDualLane_en.pdf - 第65页

5 Working with the machine 5.1 Controls and displays Instruction Guide ASM ProcessLens Dual-lane 06/2018 75 5.1.2 Description All the controls can be reached by a 1.40 m tall person. Programmable tower lamp with buzzer (…

4 Setting up and commissioning

4.3 Setting up the machine

64 Instruction Guide ASM ProcessLens Dual-lane 06/2018

4.3.3.3 Fixing the monitors

► Install and secure the monitor in the bracket using 4x M4 x 8mm screws with washer.

► Insert the power cable.

► Insert and tighten the screws of the VGA cable.

4.3.4 Tools and equipment

You will need the following tools and equipment to adjust the height of your machine:

●

Open-ended wrench SW 19, SW 30, SW 36

●

One or two machine spirit level(s): accuracy 0.02 mm/m

●

Forklift truck (specification see 4.1.4.3 "Means of transport" [}57]).

4.3.5 Adjusting the machine height

The machine can be set at any PCB conveyor height within the following range:

●

900 mm ± 15 mm

●

930 mm ± 15 mm

●

950 mm ± 15 mm

CAUTION

Foot spacers

When using the 950 ± 15 mm PCB conveyor height, foot spacers are required to maintain

ASM ProcessLens Dual-lane measurement accuracy and stability.

NOTICE

PCB conveyor height

The PCB conveyor height is the distance between the top edge of the PCB conveyor belt

and the bottom edge of the machine feet.

5 Working with the machine

5.1 Controls and displays

Instruction Guide ASM ProcessLens Dual-lane 06/2018 75

5.1.2 Description

All the controls can be reached by a 1.40 m tall person.

Programmable tower lamp with buzzer

(see fig. "Controls and displays" [}74])

The programmable tower lamp is used to signal operating statuses and malfunctions of the

machine. The buzzer indicates when an alert has occurred. The sequence of colors of the tower

lamps is red - amber - green.

The programmable tower lamp functionality allows the operator to assign a combination of the fol-

lowing tower lamps conditions to machine events:

Condition Possible states Frequency of flashes

Green On

Off

Pulse

Pulse Frequency (ms)

Amber On

Off

Pulse

Pulse Frequency (ms)

Red On

Off

Pulse

Pulse Frequency (ms)

Buzzer On

Off

Pulse Frequency (ms)

LCD monitor

(see fig. "Controls and displays" [}74])

There is a flat LCD monitor at the front side of the ASM ProcessLens Dual-lane machine. A LCD

monitor with a touch-sensitive surface (touchscreen) as an option is available.

Keyboard

(see fig. "Controls and displays" [}74])

The keyboard and mouse are located beneath the monitor.

CAUTION

Risk of collision of personal with monitor and keyboard holder

Risk of collision of the front hood with the arm where the monitor, keyboard and mouse are

mounted.

Key switch ON/OFF

(see fig. "Controls and displays" [}74])

Turn on the control power manually and switch the conveyor into pass through mode when the PC

is down.

► Close the GUI program.

► Switch off the machine by the main switch.

► Wait for 30 sec switch on the machine by the main switch.

► Turn the key switch to the left and release to turn on the control power.

► Turn the key switch to the right.

The conveyor set to pass through running mode.

4 Setting up and commissioning

4.3 Setting up the machine

66 Instruction Guide ASM ProcessLens Dual-lane 06/2018

4.3.6 Levelling the machine

► Level the machine in the X and Y direction with the help of the machine spirit level.

Fig.39: Position of the machine spirit level in the X and Y direction

► Place the machine spirit levels (1) in the X and then the Y direction on the linear guide rails.

► Measure the distance between the upper edge of the PCB conveyor belt and the floor. This

distance should be the range from to 950 mm, if the height of the machine is to be set to

950mm. Other heights also apply.

► Turn the bottom screw nut (item 4 in fig. "Presetting the height of the machine feet" [}65]) of

all four machine feet, so that the fluid in the machine spirit level does not deviate from its zero

point (tolerance within ±0.05mm) at the required conveyor height.

► Check the required board conveyor height.

► Once the machine has been levelled, tighten the top secure nut (item 3 in fig. "Presetting the

height of the machine feet" [}65]) to clamp all machine feet.

► Use the spirit level to check that the machine is precisely levelled (tolerance within

±0.05mm).