00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第257页

10 Repairs to SmartFeeder 24 - 104 mm X 10.7 Drives and gears Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 257 10.7.4.1 Removing the foil disposal drive ► Remove the left and right side cover (see 10.3.1 &quot…

100%1 / 286
10 Repairs to SmartFeeder 24 - 104 mm X
10.7 Drives and gears
256 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
► Guide the tape drive cable through the marked
opening to the other side of the feeder module.
(1)
Make sure that the cable is on the right side of
the feeder module in the cable duct.
► Carefully place the feeder module on its right
side.
► Press the connector of the tape drive cable into
the marked connection on the control board.(2)
► Fasten the left and the right side covers (see .
(see 10.3.1 "Removing/fitting the left side
plate" [}230] and 10.3.2 "Removing/fitting the
right front cover" [}231]).
10.7.4 Foil drive (hybrid stepping motor)
Required spare part
Fig.92: Foil disposal drive for hybrid stepping motor assembly
Feeder module Item no. Designation
SmartFeeder 24 – 104 mm X 03116587Sxx Hybrid stepping motor assembly X24-104Smart
Required tools
●
Phillips screwdriver 0.6Nm
●
Phillips screwdriver 0.9Nm
●
TORX screwdriver 0.6Nm, size T8
●
Gauge for foil disposal motor X24-104, item no. 03130747-xx
●
Circlip pliers for outer rings 3-10 mm
●
Tweezers
10 Repairs to SmartFeeder 24 - 104 mm X
10.7 Drives and gears
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 257
10.7.4.1 Removing the foil disposal drive
► Remove the left and right side cover (see 10.3.1
"Removing/fitting the left side plate" [}230] and
10.3.2 "Removing/fitting the right front
cover" [}231]).
► Carefully place the feeder module on its right
side.
► Unplug the connector on the foil disposal drive
cable from its connection on the control
board.(1)
► Guide the cable through the marked opening(2)
to the other side of the feeder module.
► Carefully place the feeder module down on its left
side.
► Remove the circlip(1) on gear stage1.
► Remove the washer (2) on gear stage1
► Remove gear stage 1.(3)
► Remove the two screws which fasten the foil dis-
posal drive.(4)
► Remove the foil disposal drive.
10.7.4.2 Fitting the foil disposal drive
► Carefully place the feeder module down on its left
side.
► Insert the foil disposal drive into the recess.
Make sure that the cable of the foil disposal drive
is on the right side.
► Run the cable in the cable duct.(1)
► Position the foil disposal drive so that you can
see the drilled holes in the feeder module base
unit, through the holes in the drive frame.(2)
► Fit the gauge as shown, with the level side point-
ing upwards, onto the pinion of the foil disposal
drive and onto the axis of shifted gear1.(3)
► Position the foil disposal drive so that the pinion
and gauge can not catch in one another.
► Fix the foil disposal drive with the two Phillips
screws ISO 7045 M2.5x8. Use a Phillips screw-
driver with 0.9Nm for this.
► Remove the gauge.
10 Repairs to SmartFeeder 24 - 104 mm X
10.7 Drives and gears
258 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
► Fit shifted gear1(1) with the smaller toothed
wheel pointing downwards, onto the axis.
Make sure that the smaller toothed wheel en-
gages down in shifted gear 2 . (2)
The large toothed wheel for the shifted gear will
engage above with the foil disposal drive pinion .
(3)
► Fit the washer into place.(4)
► Secure shifted gear 1 with a new circlip.(5)
► Guide the foil disposal drive cable through the
marked opening to the other side of the feeder
module.(1)
Make sure that the cable is on the right side of
the feeder module in the cable duct.
► Carefully place the feeder module on its right
side.
► Plug the connector for the foil disposal drive
cable into the marked connection on the control
board.(2)
► Fasten the left and the right side covers (see .
See also
2 10.3.1 "Removing/fitting the left side plate" [}230]
2 10.3.2 "Removing/fitting the right front cover" [}231]