00198505-01_SM_SIPLACE_SmartFeeder_EN.pdf - 第258页
10 Repairs to SmartFeeder 24 - 104 mm X 10.7 Drives and gears 258 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 ► Fit shifted gear1 (1) with the smaller toothed wheel pointing downwards, onto the axis. Make s…
10 Repairs to SmartFeeder 24 - 104 mm X
10.7 Drives and gears
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 257
10.7.4.1 Removing the foil disposal drive
► Remove the left and right side cover (see 10.3.1
"Removing/fitting the left side plate" [}230] and
10.3.2 "Removing/fitting the right front
cover" [}231]).
► Carefully place the feeder module on its right
side.
► Unplug the connector on the foil disposal drive
cable from its connection on the control
board.(1)
► Guide the cable through the marked opening(2)
to the other side of the feeder module.
► Carefully place the feeder module down on its left
side.
► Remove the circlip(1) on gear stage1.
► Remove the washer (2) on gear stage1
► Remove gear stage 1.(3)
► Remove the two screws which fasten the foil dis-
posal drive.(4)
► Remove the foil disposal drive.
10.7.4.2 Fitting the foil disposal drive
► Carefully place the feeder module down on its left
side.
► Insert the foil disposal drive into the recess.
Make sure that the cable of the foil disposal drive
is on the right side.
► Run the cable in the cable duct.(1)
► Position the foil disposal drive so that you can
see the drilled holes in the feeder module base
unit, through the holes in the drive frame.(2)
► Fit the gauge as shown, with the level side point-
ing upwards, onto the pinion of the foil disposal
drive and onto the axis of shifted gear1.(3)
► Position the foil disposal drive so that the pinion
and gauge can not catch in one another.
► Fix the foil disposal drive with the two Phillips
screws ISO 7045 M2.5x8. Use a Phillips screw-
driver with 0.9Nm for this.
► Remove the gauge.
10 Repairs to SmartFeeder 24 - 104 mm X
10.7 Drives and gears
258 Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017
► Fit shifted gear1(1) with the smaller toothed
wheel pointing downwards, onto the axis.
Make sure that the smaller toothed wheel en-
gages down in shifted gear 2 . (2)
The large toothed wheel for the shifted gear will
engage above with the foil disposal drive pinion .
(3)
► Fit the washer into place.(4)
► Secure shifted gear 1 with a new circlip.(5)
► Guide the foil disposal drive cable through the
marked opening to the other side of the feeder
module.(1)
Make sure that the cable is on the right side of
the feeder module in the cable duct.
► Carefully place the feeder module on its right
side.
► Plug the connector for the foil disposal drive
cable into the marked connection on the control
board.(2)
► Fasten the left and the right side covers (see .
See also
2 10.3.1 "Removing/fitting the left side plate" [}230]
2 10.3.2 "Removing/fitting the right front cover" [}231]
10 Repairs to SmartFeeder 24 - 104 mm X
10.8 Foil rocker
Service Manual SIPLACE SmartFeeder 4 - 104 mm X 11/2017 259
10.8 Foil rocker
10.8.1 Foil rocker assembly
Required spare part
Fig.93: Rocker X24Smart assy.
Feeder module Pos Item no. Designation
SmartFeeder 24mmX 1 03112580- xx Rocker X24Smart assy.
2 03115946- xx Axis /D4 foil rocker X24Smart
SmartFeeder 32mm X 1 03117224- xx Rocker X32Smart assy.
2 03117226- xx Axis /D4 foil rocker X32Smart
SmartFeeder 44mm X 1 03120852- xx Rocker X44Smart assy.
2 03120870- xx Axis /D4 foil rocker X44Smart
SmartFeeder 56mm X 1 03114910- xx Rocker X56Smart assy.
2 03120625- xx Axis /D4 foil rocker X56Smart
SmartFeeder 72mm X 1 03114275- xx Rocker X72Smart assy.
2 03116314- xx Axis /D4 foil rocker X72Smart
SmartFeeder 88mm X 1 03120979- xx Rocker X88Smart assy.
2 03120973- xx Axis /D4 foil rocker X88Smart
SmartFeeder 104mm X 1 03121137- xx Rocker X104Smart assy.
2 03121134- xx Axis /D4 foil rocker X104Smart
SmartFeeder
24 - 104 mm X
3 03092093- xx Pressure spring 0.7x7.5x35.8mm
4 03113174- xx Rocker housing X24-104
5 03033796- xx RF-SN75-2.5 x 6-9.8
6 03100381- xx Light barrier transmitter flat assy. X8S-
mart
7 03063591- xx Cable for light barrier transmitter X2x8
Required tools
●
Phillips screwdriver 0.6Nm
●
Flat-bladed screwdriver size 1
●
TORX screwdriver 0.6Nm, size T8