TM4642.TM4406.PickupMACS.pdf - 第4页
SMT Software Engineering Group IM Ope ration s Y A MAHA MOTOR CO ., L TD. MDOC-SOFT50 177 4/ 23 2. Summary This function stabilizes pick up condition, mainly targeting small parts. I t cons ists of the follo wing two f…
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD.
MDOC-SOFT50177
3/23
1. Target Model
Pickup MACS function consists of two functions [Feeder MACS] and [Nozzle MACS].
The target model and version of Feeder MACS are as follows.
Table1.1 Target model and version (Feeder MACS)
Target Model Target Version Remarks
YS24 Series
YS24X Series
YS12 Series, YS100
YS88, YSH20, YSH2S
YC8
VGOS V3.31 STD R1.000 and later
Y.FacT V1.31 STD R1.000 and later
The target machine is
equipped SS feeder.
The target model and version of Nozzle MACS are as follows.
Table1.1 Target model and version (Nozzle MACS)
対象機種 Target Version Remarks
YS24 Series
YS24X Series
YS12 Series, YG12,
YS100
VGOS V3.31 STD R1.000 and later
Y.FacT V1.31 STD R1.000 and later
The machine equipped
FNC is un-supported.
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD.
MDOC-SOFT50177
4/23
2. Summary
This function stabilizes pick up condition, mainly targeting small parts. It consists of the
following two functions.
- Feeder MACS
- Nozzle MACS
It is more effective to use these two functions together. However, it is possible to individually
select either one on [Machine Setting].
2.1. Feeder MACS
Feeder MACS detects a feeder set position, and corrects its pick up position without a manual
teaching.
A Feeder MACS correction value is cleared when the machine shut down or the feeder is
detached from the machine. In that case, Feeder MACS is executed again at the next pick up
action.
When the following buttons are pressed, Feeder MACS is always executed.
- The [Parts Adjust] - [Pickup] button
- The [Teach] - [Trace] button
When Feeder MACS is failed, pick up is executed without a Feeder MACS correction.
2.2. Nozzle MACS
Nozzle MACS detects a nozzle position, and calculates its appropriate pick up position.
The correction value is cleared when an operation concerning a nozzle change is executed,
such as loading board data, pick up error, or Emergency Stop etc.
You can specify whether or not to execute Nozzle MACS again after which operation.
Refer to [3. Setting].
When Nozzle MACS is failed, pick up is executed without a Nozzle MACS correction.
SMT Software Engineering Group
IM Operations YAMAHA MOTOR CO., LTD.
MDOC-SOFT50177
5/23
3. Setting
Settings to use this function are as follows.
3.1. Machine Setting
In [Machine] - [Setting] - [Machine Data] - [Precision] - [Pickup MACS], set each item.
Fig.3.1 “Pickup MACS” Settings
< Contents of Pickup MACS common setting items >
Items Explanation Input range Initial value
Pickup MACS Size X(mm)
Pickup MACS Size Y(mm)
Input the target parts size. This
function executes parts size smaller
than input value in this item.
000.000–
999.999(mm)
X 0.350(mm)
Y 0.650(mm)
Sim Pick Parts Size Limit
X(mm)
Sim Pick Parts Size Limit Y
(mm)
Input the parts size which lower limit
executing simultaneous pickup. The
parts of the size of less than an input
value do not execute simultaneous
pickup.
000.000–
999.999(mm)
X 0.25(mm)
Y 0.45(mm)
Common Setting items
Switch [Feeder MACS] setting items
and [Nozzle MACS] setting items.